Simplicity 24HP manual Check / Fill Transmission OIL, Transmission OIL Filter Change

Page 31

Regular Maintenance

CHECK / FILL TRANSMISSION OIL

Oil Type: 20W-50 conventional detergent motor oil.

1.Check the oil level when the unit is cold. Raise the seat plate to gain access to the transmission oil reservoirs (A, Figure 26). The oil should be up to the “FULL COLD” mark (B). If the oil is below this level, proceed to step 2.

2.Before removing the reservoir cap, make sure the area around the reservoir cap and fill neck of the reservoir is free of dust, dirt, or other debris.

Remove the reservoir cap.

3.Add oil up to the “FULL COLD” mark (B, Figure 26).

4.Reinstall the reservoir cap.

A

B

Figure 26. Transmission Oil Reservoirs

A.Transmission Oil Reservoirs

B.“FULL COLD” Mark

Maintenance

TRANSMISSION OIL FILTER CHANGE

Change Interval: Every 200 Hours

1.Locate the transmission oil filters (A, Figure 27) underneath the rear of the machine on the transmissions.

2.Remove the three 1/4” filter guard screws (C) and the filter guard (B).

3.Clean the area around the filter base and remove the filter.

4.Apply a film of new oil to the gasket of the new replacement filter. After the oil has drained, thread the new filter onto the filter base until the gasket makes contact, then tighten 3/4 of a turn more.

5.Reinstall the filter guard with the three 1/4” filter guard screws

6.Using a hex bit swivel socket or a modified allen wrench remove the top port plug from the transmissions.

7.Remove the transmission reservoir cap and fill with oil until oil appears at the bottom of the transmission’s top port (approximately 2 qts (1,89L).

8.Reinstall the top port plug and tighten to 15 ft lbs (20,38 Nm).

9.Continue to add oil to the transmission oil reservoirs until the oil level reaches the “FULL COLD” mark. Reinstall the oil reservoir cap.

10.Repeat this process for the other side of the machine.

A

B

D

C

Figure 27. Transmission (Left Side Shown.)

A.Transmission Oil Filter

B.Filter Guard

C.1/4” Filter Guard Screws

D.Top Port Plug

11.Run the unit for several minutes and check the transmission oil level.

IMPORTANT NOTE: Use caution after changing the filter; air in the hydraulic system may affect the responsiveness of the ground speed control levers. Repeat step 11 until the air is out of the system.

28

www.simplicitymfg.com www.snapper.com

Page 30 Page 32
Image 31
Page 30 Page 32
Contents 24HP Zero-Turn Riders OPERATOR’S ManualPage Date Purchased Table of Contents Safety Rules & Information Operating SafetySlope Operation Retaining Walls, Drop-offs, and Water General Operation Slope Operation Safety Rules and InformationSafe Handling of Gasoline Service & MaintenanceCE Identification TAG Markings Identification NumbersCE Export Models Safety DecalsSafety Decals North American ModelsOperational Safety Checks Safety Interlock SystemNorth American Models only Safety Interlock System Export Models only Safety Interlock SystemServicing Safety IconsNorth American Safety Icons CE Export Safety IconsControl Functions Features & ControlsTransmission Oil Fill PTO SwitchSeat Adjustment Lever Hour MeterOperation General Operating SafetyChecks Before Starting Stopping the Rider and Engine Starting the EnginePushing the Rider by Hand Reverse Travel Practice Zero Turn Driving PracticeSmooth Travel Forward Travel PracticeTurning Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Executing TurnsInstallation Mower Removal InstallationRemoval Tall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassProper Broadcast Mowing When and How Often to MowMowing Methods Mowing PatternsProper Mulching Attaching a TrailerBefore Every Spring Each Hours 100 200 Fall Use Regular MaintenanceCheck Transmission Oil Change Transmission Oil Filter Arm Pivot LubricationGrease OilRemoving the Mower Blade Servicing the Mower BladesInspecting the Mower Blades Nail Reinstalling the Mower Blades Sharpening the Mower Blade Balancing the Mower BladesTire Pressure Check Tire PressuresAdding Fuel Fuel FilterChange Engine OIL & Filter Engine MaintenanceTransmission OIL Filter Change Check / Fill Transmission OILChange Interval Every 200 Hours Cleaning the Battery and Cables Battery MaintenanceStorage Troubleshooting the Rider Troubleshooting, Adjustments, & ServiceTroubleshooting the Mower Troubleshooting, Adjustments, & ServiceStreaking Troubleshooting Common Cutting ProblemsGround Speed Control Lever Adjustment Seat AdjustmentSeat Position Adjustment Cutting Height Adjustment Speed Balancing AdjustmentNeutral Adjustment Suspension Adjustment A. Front Shock Adjustment Collar Parking Brake AdjustmentBlade Brake Check PTO Clutch AdjustmentOrient Blades Side-to-Side Mower Deck LevelingRoller BAR Leveling Select Models Mower Belt ReplacementBattery Charging Hydraulic Pump Drive Belt ReplacementTechnical Manuals SpecificationsPage Belts and Blades Tractor Product Quick Specs
Top Page Image Contents