Simplicity 7800071, 7800072 instruction sheet Mower Deck Leveling, Orient Blades Side-to-Side

Page 32

Troubleshooting, Adjustments, & Service

Figure 27. Orient Blades Side-to-Side

MOWER DECK LEVELING

Perform these adjustments on a flat level surface. Be sure to check and adjust tire pressures before leveling the mower deck

SIDE-TO-SIDE LEVELING

1.With the mower installed, place the rider on a smooth, level surface such as a concrete floor. Turn the front wheels so they are straight.

2.Check for bent blades and replace if necessary.

3.Place the mower cutting height lever in the fourth adjustment notch from the bottom. Arrange the out- side mower blades so that they are pointing from side-to-side (Figure 27).

4.Measure the distance between the outside tips of each blade and the ground (Figures 27 & 28). The measurement should be 3” (7,6 cm), +/-1/8” (3mm). If there is more than 1/8” (3mm) difference between the measurements on each side, proceed to step 5. If the difference is 1/8” (3mm) or less, proceed to step 6.

5.Use the rear leveling nuts (A, Figure 29) to adjust the side-to-side leveling of the deck. Repeat step 4 if necessary.

FRONT-TO-BACK LEVELING

6.Arrange the blades so they face front-to-back (Figure 30).

7.Measure the distance from the ground to the front tip of the center blade and from the ground to the rear tip of the rear blades (Figures 28 & 30). The front tip of the front blade should be 1/4" (6mm) higher than the rear tips of the rear blades. If not, proceed with steps 8 - 9.

A

B

C

Figure 28. Measure Blade Tips to Ground

A.

Mower Deck

C. Level Ground

B.

Blade Tip

 

A

Figure 29. Mower Leveling - Side-to-Side A. Rear Leveling Nuts

(Left side shown, right side hidden)

Figure 30. Orient Blades Front-to-Back

(Continued Next Page)

28

Image 32
Contents Operator’s Manuals Paper SizePress BinderyPage OPERATOR’S Manual Page Table of Contents Safety Rules & Information Safety Rules and Information From PreviousTowing Identification Numbers CE Identification TAG MarkingsSafety Decals Safety DecalsSafety Interlock System Operational Safety ChecksChoke Control FunctionsMotion Control Levers Features & Controls General Operating Safety Checks Before StartingOperation Starting the EngineStopping the Rider & Engine Pushing the Rider by HandZero Turn Driving Practice Smooth TravelForward Travel Practice Reverse Travel PracticePractice Turning Around a Corner Executing an End-Of-Row Zero TurnRemoval Mower Removal InstallationAttaching a Trailer Installation Regular Maintenance Before Every Spring Each Hours 100 250 Fall UseRegular Maintenance LubricationService Interval Every 10 Hours or As Required Servicing the Mower BladesEngine Maintenance Check Tire PressuresChecking / Adding Fuel Fuel FilterStorage Battery MaintenanceCleaning the Battery and Cables Troubleshooting, Adjustments, & Service Troubleshooting the RiderTroubleshooting, Adjustments, & Service Troubleshooting the MowerSeat Adjustments Motion Control Lever AdjustmentSpeed Balancing Adjustment Seat Position AdjustmentRoller BAR Adjustment Motion Control Lever Friction AdjustmentCutting Height Adjustment Neutral Adjustments Brake Adjustment Parking Brake AdjustmentFront Suspension Adjustment Select Models PTO Clutch Adjustment Blade Brake CheckMower Deck Leveling Orient Blades Side-to-SideIf Equipped Deck Timing ROD AdjustmentRoller BAR Leveling Transmission Drive Belt Replacement Battery ChargingMower Belt Replacement PRY Belts Over PulleysFuse Replacement CE Compliance Specifications Transmissions DimensionsEngine ChassisTechnical Manuals Replacement PartsMaintenance Items