Poulan RTE113, RTE114 instruction manual Adjusting Assist Handle, Attaching the Shield

Page 4

WARNING: If received assembled, review all assembly steps to ensure your unit is properly assembled and all fasteners are secure.

ADJUSTING ASSIST HANDLE

1.Place unit on a flat surface.

2.Loosen and remove wing nut and bolt from assist handle.

3.Firmly push the assist handle over the tube. To make installation easier, tilt han- dle toward trigger housing while pushing down (see illustration).

4.Reinstall bolt in handle. Thread wing nut onto bolt.

5.Adjust the handle up or down the tube to a comfortable position; tighten wing nut se- curely.

Assist handle

Trigger

Housing

Tube

ATTACHING THE SHIELD

WARNING: The shield must be prop- erly installed. If shield is not properly installed, damage to unit (including motor failure) will re- sult. The shield provides partial protection to the operator and others from the risk of thrown objects. Your unit is equipped with a line limiter blade, which cuts excess line to the proper length while running. The line limiter blade (on underside of shield) is sharp and can cut you.

NOTE: If shield is not properly installed, dam- age to unit (including motor failure) will result. Edge guide must be positioned on shield prior to installation on motor housing (see following il- lustration).

Edge Guide

Shield

1.Hold shield at angle to the trimmer motor housing. Align the front locking tab of the shield with the front notch of the motor housing (see illustration below).

2.Move shield toward motor housing, en- suring trimmer head passes through opening in shield without catching on shield locking tabs.

3.Tilt front of the shield towards front notch of motor housing. Push front locking tab of the shield into the front notch of the mo- tor housing. An audible snap must be heard. Ensure the cutting head remains free to rotate and the line is not caught be- tween the shield and the motor housing.

4.Push back of the shield toward the motor housing as illustrated until the rear locking tabs snap securely into the rear notches. Make sure the shield is assembled to the unit as shown in the illustration below and in the KNOW YOUR UNIT section of this manual.

Rear

Front Locking Tab

 

 

 

 

 

 

Trimmer

Locking

 

 

 

 

Front

Tabs

 

 

 

 

Motor

 

 

 

 

Notch

 

 

 

 

 

 

 

 

Housing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Rear

Trimmer Notches

Head

CAUTION: Sharp line limiter blade

4

Image 4
Contents Advertencia AvertissementOperator Safety Electrical SafetyUnit Safety Cutting SafetyMaintenance Safety Transporting and StorageAdjusting Assist Handle Attaching the ShieldOperating Instructions Correct Operating Position Advancing the Cutting LineBefore Each USE After Each USEUser Replaceable Service Parts Troubleshooting Table Cause RemedyINC Policy of Electrolux Home Prod