Poulan 530163516 Replacing the Cutting Head, Carburetor Adjustment, Seasonal Storage, Fuel System

Page 13

REPLACING THE CUTTING HEAD

1.Align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup.

2.Insert a small screwdriver into aligned holes. This will keep the shaft from turn- ing while removing and installing trimmer head.

Screwdriver

3.While holding the screwdriver in position, remove trimmer head by turning clock- wise.

4.Thread replacement trimmer head onto the shaft by turning counterclockwise. Tighten until secure.

5.Remove the screwdriver.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without trimmer head moving or spinning (idle too fast) or stalling (idle speed too slow). S Turn idle speed screw clockwise to increase engine speed if engine stalls or

dies.

STurn idle speed screw counterclockwise to decrease engine speed if trimmer head moves or spins at idle.

WARNING: Recheck the idle speed after each adjustment. The trimmer head must not move or spin at idle speed to avoid serious injury to the operator or others.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during most of this pro- cedure. Wear your protective equipment and observe all safety precautions. After making adjustments, the trimmer head must not move/spin at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is released.

S The trimmer head moves/spins at idle.

Air Filter

Cover

Idle Speed

Screw

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

WARNING: Perform the following steps after each use:

SAllow engine to cool before storing or trans- porting.

SStore unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time: S Clean the entire unit before lengthy

storage.

SStore in a clean dry area.

SLightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to

another.

SReplace your gasoline can if it starts to rust.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Manual de Instrucciones Manuel d’Instructions PP4000C Operator SafetyFuel Safety Unit / Maintenance SafetyLine Trimmer Safety Transporting and StorageBLOWER/VACUUM Safety Edger SafetyBrushcutter Safety Hedge Trimmer Safety Pole Pruner Safety Cultivator SafetyOr broken Snow Thrower SafetyAdjusting the Handle Installing Trimmer ATTACH- MentAttaching Shield HOW to Stop Your Unit ON/OFF Switch ChokeKnow Your Trimmer Primer BulbStarting a Warm Engine HOW to Start Your UnitStarting a Flooded Engine Operating the Coupler Installing Optional ATTACH- MentsOperating Position Trimmer Line AdvanceRightWrong Cutting MethodsClean AIR Filter Inspect and Clean Unit and LA- BelsCheck for Loose Fasteners and Parts Check for Damaged or Worn PartsReplacing the Cutting Head Carburetor AdjustmentSeasonal Storage Fuel SystemTroubleshooting Table Cause Remedy Agency and POULAN/WEED EATER, Divi

530163516 specifications

The Poulan 530163516 is a high-performance trimmer head that enhances the functionality of various compatible string trimmers, making it a popular choice among landscaping professionals and gardening enthusiasts. Its design and technology cater to the demands of heavy-duty trimming, offering durability and ease of use.

One of the standout features of the Poulan 530163516 is its innovative bump feed system. This mechanism allows users to effortlessly release more line with a simple bump on the ground. This eliminates the need for frequent stops to manually feed the line, thereby increasing efficiency during trimming tasks. The bump feed system is designed to work seamlessly, ensuring that the line is dispensed consistently for optimal performance.

The trimmer head is equipped with a robust construction that ensures it withstands the rigors of outdoor use. Made from high-quality materials, it is resistant to wear and tear, making it a reliable tool for long-lasting service. The steel components in the head provide added strength, allowing it to handle heavy usage without compromising on performance.

Another significant characteristic of the Poulan 530163516 is its compatibility with a wide range of trimmer models. This versatility makes it a highly sought-after accessory for users who may already own various brands of trimmers. The universal fit allows for easy installation without the need for specialized tools, making it convenient for users to upgrade their equipment quickly.

The design of the trimmer head also prioritizes ease of line loading. It features a quick-load system that simplifies the process of replacing the line, significantly reducing downtime. Users can either use pre-cut lengths or easily cut their desired lengths of line, enhancing the convenience of operation.

In terms of performance, the Poulan 530163516 is engineered to deliver consistent cutting power, allowing users to tackle tough grasses and weeds without straining their equipment. The head's efficiency translates into a cleaner, more precise cut, which is crucial for maintaining landscaped areas and gardens.

In summary, the Poulan 530163516 trimmer head combines advanced technologies with user-friendly features. Its durability, compatibility, and efficient design make it a top choice for anyone looking to enhance their trimming capabilities. Whether you're a professional landscaper or a home gardener, this trimmer head provides the reliability and performance needed for effective outdoor maintenance.
Top Page Image Contents