Poulan 115248826, 952711944 HOW to Stop Your Unit, HOW to Start Your Unit, Starting a Cold Engine

Page 11

WARNING: Alternative fuels (not gas- oline) such as E--15 (15% alcohol), E--20 (20% alcohol), E--85 (85% alcohol) are NOT classified as gasoline and are NOT approved for use in 2--stroke gasoline engines. Use of alternative fuels will cause problems such as: improper clutch engagements, overheating, vapor lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor components, etc. Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

HOW TO STOP YOUR UNIT

SRelease the throttle trigger.

S Push and release the engine ON/STOP switch. The switch will automatically return to the ON position. Wait 5 seconds before attempting to restart unit to allow switch to reset.

ON/STOP switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the muffler. A hot muffler can cause serious burns.

Starting position

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE

NOTE: DO NOT squeeze the throttle trigger until the engine has started and runs.

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE position.

Primer bulb

Choke lever

Muffler

 

 

Starter handle

4.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

5.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

6.Pull starter rope sharply until engine runs, but no more than 6 pulls. NOTE: If the en- gine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to STARTING A FLOODED ENGINE.

7.Once the engine starts, allow it to run 10 seconds. Squeeze throttle trigger and allow the unit to run for 30 more seconds at RUN. Release throttle trigger. NOTE: If engine dies with the choke lever in the RUN posi- tion, move the choke lever to FULL CHOKE then back to HALF CHOKE and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move choke lever to the FULL CHOKE position, then to the HALF CHOKE posi- tion to set fast idle.

2.Pull starter rope sharply until engine runs, but no more than 6 pulls.

3.Allow engine to run 15 seconds, then move the choke lever to RUN.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the RUN position; then, pull the rope to clear the engine of excess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are:

MODEL:

Edger . . . . . . . . . . . . . . . . . . . . . PPB1000E Cultivator . . . . . . . . . . . . . . . . . . PPB2000T Blower . . . . . . . . . . . . . . . . . . . . PPB3000B Brushcutter . . . . . . . . . . . . . . . . PPB4000C Pruner . . . . . . . . . . . . . . . . . . . . PPB5000P Pruner . . . . . . . . . . . . . . . . . . . . PPB5500P

WARNING: Always stop unit and dis- connect spark plug before removing or instal- ling attachments.

REMOVING TRIMMER ATTACH- MENT (OR OTHER OPTIONAL ATTACHMENTS)

CAUTION: When removing or installing at- tachments, place the unit on a flat surface for stability.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Table of ContentsIdentification of Safety Symbols Always wear face or dust mask if operation is dusty Safety RulesOperator Safety Optional AttachmentsAdditional Safety Rules Unit / Maintenance SafetyFuel Safety Line Trimmer SafetyHandlebar Edger SafetyBLOWER/VACUUM Safety Brushcutter SafetyCut from your right to your left Cultivator SafetyHedge Trimmer Safety Pole Pruner SafetyAnother Snow Thrower SafetyHigh speed causing injury Know how to stop quicklyAttaching the Shield AssemblyInstalling Trimmer ATTACH- Ment Operation Starting a Warm Engine HOW to Stop Your UnitHOW to Start Your Unit Starting a Cold EngineAttachmentLOOSEN Knob Installing Optional ATTACH- MentsOperating Position Cutting MethodsCheck for Damaged or Worn Parts MaintenanceCheck for Loose Fasteners and Parts Service and Adjustments Fuel System Carburetor Idle Speed AdjustmentSeasonal Storage Other Troubleshooting Table Cause RemedyEngine Ligations The U.S. Environmental Limited WarrantyStatesville Road Canada, contactIntermediate 125 hours Extended 300 hours

115248826, 952711944 specifications

The Poulan 952711944 and 115248826 are essential components designed to enhance the performance and usability of outdoor power equipment, particularly chainsaws and trimmers. Known for their reliability and efficiency, these parts exemplify Poulan's commitment to delivering high-quality products for both professional users and homeowners.

One of the standout features of the Poulan 952711944 is its durability. Constructed with high-grade materials, it is built to withstand the demanding conditions that come with outdoor work. This durability ensures that the part can resist wear and tear, enabling it to maintain peak performance over an extended period. Furthermore, the precise engineering of the 952711944 ensures compatibility with several Poulan models, making it a versatile choice for users looking to replace or upgrade their equipment.

In terms of technology, the 952711944 incorporates advanced design principles that focus on ease of use and safety. Its ergonomic design allows for straightforward installation, minimizing downtime and getting users back to work quickly. The component is engineered to fit snugly, reducing the risk of vibration during operation, which in turn aids in accuracy and comfort.

On the other hand, the Poulan 115248826 is equally impressive, providing essential support for trimmers. It boasts a lightweight construction, allowing for enhanced maneuverability during operation. This is particularly crucial for those who need to navigate tight spaces or maintain large areas without fatigue. The design also features a user-friendly interface, making it accessible for individuals at any skill level.

Both the 952711944 and 115248826 incorporate technologies that prioritize fuel efficiency and reduced emissions. This eco-conscious approach is particularly relevant in today’s market, where environmental sustainability is a growing concern. Poulan’s advancements in this area demonstrate their commitment to producing equipment that not only performs well but also respects the environment.

In summary, the Poulan 952711944 and 115248826 are pivotal components that embody the brand's dedication to quality and innovation. With their robust build, user-friendly designs, and environmentally friendly technologies, these parts are ideal for anyone looking to enhance the performance of their outdoor power equipment. Whether for professional landscaping or home gardening, the reliability of these components speaks for itself.
Top Page Image Contents