Poulan 115248826, 952711944 Carburetor Idle Speed Adjustment, Seasonal Storage, Fuel System

Page 15

Screwdriver

3.While holding the screwdriver in position, remove trimmer head by turning clock- wise (looking from bottom of unit).

4.Thread replacement trimmer head onto the shaft by turning counterclockwise. Tighten until secure.

5.Remove the screwdriver.

CARBURETOR IDLE SPEED ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head, blade or any optional attachment will be spinning during most of this procedure. Wear your protective equipment and observe all safe- ty precautions. After making adjustments, the trimmer head, blade or any optional attachment must not move/spin at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is released.

S The trimmer head, blade or optional attachment moves/spins at idle.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

To adjust idle speed:

Allow engine to idle. Adjust speed until engine runs without trimmer head, blade or optional attachment moving or spinning (idle too fast) or stalling (idle speed too slow).

STurn idle speed screw clockwise to increase

engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed if trimmer head, blade or optional attachment moves or spins at idle.

WARNING: Recheck the idle speed after each adjustment. The trimmer head, blade or optional attachment must not move or spin at idle speed to avoid serious injury to the operator or others.

Idle Speed Screw

Air Filter

Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow engine to cool before storing or trans-

porting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position

unit so that any sharp object cannot acci- dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

SClean the entire unit before lengthy storage. S Store in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container.

Follow the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

HELPFUL TIP

During storage of your gas/ oil mixture, the oil will sepa- rate from the gas.

We recommend that you shake the gas can weekly to insure proper blending of the gas and oil.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Table of ContentsIdentification of Safety Symbols Always wear face or dust mask if operation is dusty Safety RulesOperator Safety Optional AttachmentsAdditional Safety Rules Unit / Maintenance SafetyFuel Safety Line Trimmer SafetyHandlebar Edger SafetyBLOWER/VACUUM Safety Brushcutter SafetyCut from your right to your left Cultivator SafetyHedge Trimmer Safety Pole Pruner SafetyAnother Snow Thrower SafetyHigh speed causing injury Know how to stop quicklyAssembly Installing Trimmer ATTACH- MentAttaching the Shield Operation Starting a Warm Engine HOW to Stop Your UnitHOW to Start Your Unit Starting a Cold EngineAttachmentLOOSEN Knob Installing Optional ATTACH- MentsOperating Position Cutting MethodsMaintenance Check for Loose Fasteners and PartsCheck for Damaged or Worn Parts Service and Adjustments Carburetor Idle Speed Adjustment Seasonal StorageFuel System Troubleshooting Table Cause Remedy EngineOther Ligations The U.S. Environmental Limited WarrantyStatesville Road Canada, contactIntermediate 125 hours Extended 300 hours

115248826, 952711944 specifications

The Poulan 952711944 and 115248826 are essential components designed to enhance the performance and usability of outdoor power equipment, particularly chainsaws and trimmers. Known for their reliability and efficiency, these parts exemplify Poulan's commitment to delivering high-quality products for both professional users and homeowners.

One of the standout features of the Poulan 952711944 is its durability. Constructed with high-grade materials, it is built to withstand the demanding conditions that come with outdoor work. This durability ensures that the part can resist wear and tear, enabling it to maintain peak performance over an extended period. Furthermore, the precise engineering of the 952711944 ensures compatibility with several Poulan models, making it a versatile choice for users looking to replace or upgrade their equipment.

In terms of technology, the 952711944 incorporates advanced design principles that focus on ease of use and safety. Its ergonomic design allows for straightforward installation, minimizing downtime and getting users back to work quickly. The component is engineered to fit snugly, reducing the risk of vibration during operation, which in turn aids in accuracy and comfort.

On the other hand, the Poulan 115248826 is equally impressive, providing essential support for trimmers. It boasts a lightweight construction, allowing for enhanced maneuverability during operation. This is particularly crucial for those who need to navigate tight spaces or maintain large areas without fatigue. The design also features a user-friendly interface, making it accessible for individuals at any skill level.

Both the 952711944 and 115248826 incorporate technologies that prioritize fuel efficiency and reduced emissions. This eco-conscious approach is particularly relevant in today’s market, where environmental sustainability is a growing concern. Poulan’s advancements in this area demonstrate their commitment to producing equipment that not only performs well but also respects the environment.

In summary, the Poulan 952711944 and 115248826 are pivotal components that embody the brand's dedication to quality and innovation. With their robust build, user-friendly designs, and environmentally friendly technologies, these parts are ideal for anyone looking to enhance the performance of their outdoor power equipment. Whether for professional landscaping or home gardening, the reliability of these components speaks for itself.
Top Page Image Contents