Husqvarna 325HS99X, 325HS75X manual Blades

Page 6

SAFETY INSTRUCTIONS

•Check that the throttle control and throttle lock move freely and that the return springs work properly.

•See instructions under the heading Start. Start the hedge trimmer and apply full throttle. Release the throttle trigger and check that the blades stop and remain stationary. If the blades move when the throttle trigger is in the idle position then the carburettor idle setting must be adjusted. See instructions under the heading Maintenance.

Stop switch

•Start the engine and make sure the engine stops when you move the stop switch to the stop setting.

Hand guard

•Check that the hand guard is fitted correctly.

•Check that the hand guard is undamaged.

Vibration damping system

•Regularly check the vibration damping units for cracks or deformation.

•Make sure the vibration damping units are securely attached to the engine unit and handle unit.

Muffler

•Never use a machine that has a faulty muffler.

•Regularly check that the muffler is securely attached to the machine.

•If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage. Never use a muffler that has a defective spark arrestor mesh.

Blades

To ensure good cutting results it is important that the contact pressure between the blades is correct. The contact pressure is adjusted by turning the screws on the underside of the bar clockwise as far as they will go. Then turn the screws anticlockwise a 1/4 turn. Lock the screws using the locking nut on the top of the bar. Check that the screws are loose enough to allow the washers under the screw heads to slide sideways.

When the blades are correctly adjusted the play between the blades should be 0,2–0,4 mm, measured at the screws. The edges of the blades are too hard to be filed. Dull blades should be sharpened using a grinder. Replace the blades if they are bent or damaged.

6 – English

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 325HS75X-SERIES 325HS99X-SERIES KEY to Symbols SymbolsContents Safety Instructions Machine′s safety equipmentPersonal protective equipment Vibration damping system MufflerBlades Gear housing General safety precautionsAssembly of the catcher accessory Fuel safetySafety instructions while working Safety instructions when using the hedge trimmerSafety instructions regarding the surroundings Transport and storageSafety instructions after completing work Basic working techniquesWhat is WHAT? What is what?Fuel Handling FuelFuelling Starting and stopping Starting and StoppingCheck before starting Cold engineWarm engine StoppingMaintenance CarburettorCorrectly adjusted carburettor MufflerHigh speed jet H Spark plug Cleaning the air filterCooling system Air filterGear housing Cleaning and lubricationMaintenance schedule Technical Data Technical dataEC-declaration of conformity Applies to Europe only Cispr 121997, EN7741140179-26

325HS75X, 325HS99X specifications

The Husqvarna 325HS99X and 325HS75X are two remarkable hedge trimmers designed for both professional landscapers and gardening enthusiasts. These models combine power, precision, and comfort, making them ideal for tackling a variety of hedging tasks.

The 325HS99X features a powerful 25.4 cc engine that delivers high performance while remaining fuel-efficient. With its long 39-inch cutting blade, operators can trim large hedges more efficiently, reducing the time spent on the job. The trimmer is equipped with a double-sided blade that cuts smoothly in both directions, allowing for faster work and cleaner cuts. This model also boasts an adjustable rear handle which can be rotated to optimize comfort during various cutting angles.

On the other hand, the 325HS75X features a slightly smaller 24.5 cc engine. Although it provides slightly lower power, it is still competent for a range of trimming tasks. The 30-inch cutting blade enables users to tackle moderate-sized hedges with ease. Like its counterpart, the 325HS75X also has a double-sided blade design, ensuring efficient operation and clean results.

Both models come equipped with Husqvarna's Anti-Vibration technology, which minimizes fatigue during prolonged use. This feature is crucial for professionals who need to use the trimmer for extended periods. Additionally, the ergonomic design of both models enhances user comfort, helping to ensure that operators maintain control even during extended sessions.

Moreover, starting these hedge trimmers is made easier thanks to Husqvarna's Smart Start technology. This system reduces the amount of effort needed to start the engine, ensuring that the trimmers are ready for action without unnecessary hassle. The air filtration system in both models helps prolong the life of the engine by keeping contaminants at bay, reducing maintenance and ensuring reliable operation over time.

In summary, the Husqvarna 325HS99X and 325HS75X hedge trimmers exemplify advanced engineering and design, making them indispensable tools for anyone serious about hedge trimming. With robust power, long blades for efficiency, and innovative features for user comfort, these hedge trimmers are built to handle the demands of both professional and household gardening tasks. Whether you're trimming dense shrubs or shaping hedges, the 325HS99X and 325HS75X offer reliability and performance that gardeners can depend on.
Top Page Image Contents