Husqvarna 232R manual Transport position, handlebar, Assembling the cutting equipment

Page 13

ASSEMBLY

Transport position, handlebar

•The handlebar can easily be turned to fit along the shaft for easier transportation and storage.

•Loosen the knob.Turn the handlebar clockwise so that the throttle handle rests against the engine.

•Now twist the handlebar around the shaft. Tighten the knob.

•Fit the transport guard to the cutting attachment.

Assembling the cutting equipment

WARNING!

!When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury.

WARNING! Never use a cutting attachment

!without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury.

IMPORTANT! If a saw blade or grass blade are to be used the machine must be equipped with the correct handlebar, blade guard and harness.

Fitting a blade guard, grass blade and grass cutter (232R)

 

G

 

F

 

E

 

D

A

B

 

 

C

L

 

M

•The blade guard (A) is fitted using 4 screws (L) and the support plate (M) as shown. CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data.

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Place the blade (D), support cup (E) and support flange

(F) on the output shaft.

•Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 232R 235R 235FR Symbols KEY to SymbolsContents Dear customer IntroductionWhat is what? What is WHAT?Personal protective equipment General Safety PrecautionsStop switch Machine′s safety equipmentThrottle lockout Vibration damping system Cutting attachment guardQuick release MufflerLocking nut Cutting equipmentSharpening grass cutters and grass blades Cutting equipmentSharpening the saw blade Trimmer head Fitting the handlebar 232R AssemblyFitting the handlebar 235R, 235FR Assembling the cutting equipment Transport position, handlebarFitting a blade guard, grass blade and grass cutter 232R Fitting the blade guard and saw blade 232R Fitting the blade guard and saw blade 235R, 235FR AM L Fitting other guards and cutting attachments 232RSpreading the load on your shoulders Adjusting the harness and clearing sawCorrect height Correct balanceFuel Handling Fuel safetyFuel Mixing FuelingCheck before starting Starting and StoppingStarting and stopping Cold engineStopping StartingWorking Techniques Basic safety rulesGeneral working instructions ABC of clearingWorking methods Forestry clearing using a saw bladeBrush cutting with a saw blade Grass clearing using a grass bladeTrimming Grass trimming with a trimmer headCarburetor MaintenanceMuffler Correctly adjusted carburetorHigh speed jet H Cooling system Cleaning the air filterBevel gear Air filterSpark plug Maintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataTechnical Data Your Warranty Rights and Obligations Federal Emission Control Warranty StatementSuper Auto Super Auto II Page T35 Trimmy Hit Trimmy Hit Pro Trimmy SII Page S35 ´z+R9¶5*¨ T45 1150255-95 ´z+R9¶5*¨ ´z+R9¶5*¨
Top Page Image Contents