Husqvarna 232R manual Working Techniques, General working instructions, Basic safety rules

Page 22

WORKING TECHNIQUES

General working instructions

IMPORTANT!

This section describes the basic safety precautions for working with clearing saws and trimmers.

If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop.

Avoid all usage which you consider to be beyond your capability.

You must understand the difference between forestry clearing, grass clearing and grass trimming before use.

Basic safety rules

1 Look around you:

To ensure that people, animals or other things cannot affect your control of the machine.

To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting attachment.

CAUTION! Do not use the machine unless you are able to call for help in the event of an accident.

2Inspect the working area. Remove all loose objects, such as stones, broken glass, nails, steel wire, string, etc. that could be thrown out or become wrapped around the cutting attachment.

3Do not use the machine in bad weather, such as dense fog, heavy rain, strong wind, intense cold, etc. Working in bad weather is tiring and often brings added risks, such as icy ground, unpredictable felling direction, etc.

4Make sure you can move and stand safely. Check the area around you for possible obstacles (roots, rocks, branches, ditches, etc.) in case you have to move suddenly. Take great care when working on sloping ground.

5Take great care when cutting a tree that is under tension. A tree that is under tension may spring back to its normal position before or after being cut. If you position yourself incorrectly or make the cut in the wrong place the tree may hit you or the machine and cause you to lose control. Both situations can cause serious personal injury.

6Keep a good balance and a firm foothold.

7Always hold the machine with both hands. Hold the machine on the right side of your body.

8Keep the cutting attachment below waist level.

9Switch off the engine before moving to another area. Fit the transport guard before carrying or transporting the equipment any distance.

10Never put the machine down with the engine running unless you have it in clear sight.

The ABC of clearing

Always use the correct equipment.

Make sure the equipment is well adjusted.

Follow the safety precautions.

Organise your work carefully.

Always use full throttle when starting to cut with the blade.

Always use sharp blades.

Avoid stones.

Control the felling direction (take advantage of the wind).

WARNING! Neither the operator of the

!machine nor anyone else may attempt to remove the cut material while the engine is running or the cutting equipment is rotating, as this can result in serious injury.

Stop the engine and cutting equipment before you remove material that has wound around the blade shaft as otherwise there is a risk of injury. The bevel gear can get hot during use and may remain so for a while afterwards. You could get burnt if you touch it.

WARNING! Watch out for thrown objects.

!Always wear approved eye protection. Never lean over the cutting attachment guard. Stones, rubbish, etc. can be thrown up into the eyes causing blindness or serious injury.

Keep unauthorised persons at a distance. Children, animals, onlookers and helpers should be kept outside the safety zone of 15 m. Stop the machine immediately if anyone approaches. Never swing the machine around without first checking behind you to make sure no-one is within the safety zone.

22 – English

Image 22
Contents 232R 235R 235FR KEY to Symbols SymbolsContents Introduction Dear customerWhat is WHAT? What is what?General Safety Precautions Personal protective equipmentStop switch Machine′s safety equipmentThrottle lockout Quick release Cutting attachment guardVibration damping system MufflerCutting equipment Locking nutSharpening grass cutters and grass blades Cutting equipmentSharpening the saw blade Trimmer head Fitting the handlebar 232R AssemblyFitting the handlebar 235R, 235FR Assembling the cutting equipment Transport position, handlebarFitting a blade guard, grass blade and grass cutter 232R Fitting the blade guard and saw blade 232R Fitting the blade guard and saw blade 235R, 235FR Fitting other guards and cutting attachments 232R AM LCorrect height Adjusting the harness and clearing sawSpreading the load on your shoulders Correct balanceFuel Handling Fuel safetyFuel Fueling MixingStarting and stopping Starting and StoppingCheck before starting Cold engineStarting StoppingGeneral working instructions Basic safety rulesWorking Techniques ABC of clearingForestry clearing using a saw blade Working methodsGrass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingMaintenance CarburetorMuffler Correctly adjusted carburetorHigh speed jet H Bevel gear Cleaning the air filterCooling system Air filterSpark plug Maintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataTechnical Data Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsSuper Auto Super Auto II Page T35 Trimmy Hit Trimmy Hit Pro Trimmy SII Page S35 ´z+R9¶5*¨ T45 1150255-95 ´z+R9¶5*¨ ´z+R9¶5*¨