Husqvarna 232R manual Maintenance, Carburetor

Page 26

MAINTENANCE

Carburetor

Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in.To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running-in period, ask your dealer/service workshop (who will have a rev counter at their disposal) to adjust your carburettor.

WARNING! The complete clutch cover and

!shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.

Function

The carburetor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburetor. The air/ fuel mixture is adjustable. Correct adjustment is essential to get the best performance from the machine.

The setting of the carburetor means that the engine is adapted to local conditions, for example, the climate, altitude, fuel and the type of 2-stroke oil.

The carburetor has three adjustment controls: L = Low speed jet

H = High speed jet

T = Idle adjustment screw

The L and H-jets are used to adjust the supply of fuel to match the rate that air is admitted, which is controlled with the throttle. If they are screwed clockwise the air/fuel ratio becomes leaner (less fuel) and if they are turned anti- clockwise the ratio becomes richer (more fuel). A lean mixture gives a higher engine speed and a rich mixture gives a lower engine speed.

The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed.

Basic setting

The basic carburetor settings are adjusted during testing at the factory. The basic setting is richer than the optimal setting and should be maintained for the first few hours the machine is in use. The carburettor should then be finely adjusted. Fine adjustment should be carried out by a skilled technician.

CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops.

Rec. idle speed 2700 rpm

Recommended max. speed: See the Technical data section.

WARNING! If the idle speed cannot be

!adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

Fine adjustment

When the machine has been ”run-in” the carburetor should be finely adjusted. The fine adjustment should be carried out by a qualified person. First adjust the L- jet, then the idling screw T and then the H-jet.

Conditions

Before any adjustments are made, make sure that the air filter is clean and the air filter cover is fitted. If you adjust the carburettor when the air filter is dirty it will result in a leaner mixture when the filter is finally cleaned. This can lead to serious engine damage.

Carefully turn both jets, L and H, so that they are midway between fully screwed in and fully screwed out.

Do not attempt to adjust the L and H jets beyond either stop as this could cause damage.

Now start the machine according to the starting instructions and let it warm up for 10 minutes.

CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti-clockwise until the cutting attachment stops.

Low speed jet L

Try to find the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/ 4 turn counter-clockwise.

+ 1/4

L

CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops.

Fine adjustment of the idle speed T

Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly adjusted when the engine

26 – English

Image 26
Contents 232R 235R 235FR KEY to Symbols SymbolsContents Introduction Dear customerWhat is WHAT? What is what?General Safety Precautions Personal protective equipmentThrottle lockout Machine′s safety equipmentStop switch Quick release Cutting attachment guardVibration damping system MufflerCutting equipment Locking nutSharpening the saw blade Cutting equipmentSharpening grass cutters and grass blades Trimmer head Fitting the handlebar 235R, 235FR AssemblyFitting the handlebar 232R Fitting a blade guard, grass blade and grass cutter 232R Transport position, handlebarAssembling the cutting equipment Fitting the blade guard and saw blade 232R Fitting the blade guard and saw blade 235R, 235FR Fitting other guards and cutting attachments 232R AM LCorrect height Adjusting the harness and clearing sawSpreading the load on your shoulders Correct balanceFuel Fuel safetyFuel Handling Fueling MixingStarting and stopping Starting and StoppingCheck before starting Cold engineStarting StoppingGeneral working instructions Basic safety rulesWorking Techniques ABC of clearingForestry clearing using a saw blade Working methodsGrass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingMaintenance CarburetorHigh speed jet H Correctly adjusted carburetorMuffler Bevel gear Cleaning the air filterCooling system Air filterSpark plug Maintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataTechnical Data Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsSuper Auto Super Auto II Page T35 Trimmy Hit Trimmy Hit Pro Trimmy SII Page S35 ´z+R9¶5*¨ T45 1150255-95 ´z+R9¶5*¨ ´z+R9¶5*¨