Husqvarna 232R Starting and Stopping, Check before starting, Starting and stopping, Cold engine

Page 20

STARTING AND STOPPING

Check before starting

•Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. Discard a blade if cracks are found.

•Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked.

•Ensure the locking nut has not lost its captive force. The nut lock should have a locking force of at least 1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm.

•Check that the blade guard is not damaged or cracked. Replace the blade guard if it is exposed to impact or is cracked.

•Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked.

•Never use the machine without a guard nor with a defective guard.

•All covers must be correctly fitted and undamaged before you start the machine.

Starting and stopping

WARNING! The complete clutch cover and

!shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.

Always move the machine away from the refuelling area before starting. Place the machine on a flat surface. Ensure the cutting attachment cannot come into contact with any object.

Make sure no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 15 metres.

Cold engine

Ignition: Set the stop switch to the start position.

Choke: Set the choke control in the choke position.

Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled.

Warm engine

Ignition: Set the stop switch to the start position.

Choke: Set the throttle to the start position by moving the choke control to the choke position and then returning it to its original position.

20 – English

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 232R 235R 235FR KEY to Symbols SymbolsContents Introduction Dear customerWhat is WHAT? What is what?General Safety Precautions Personal protective equipmentThrottle lockout Machine′s safety equipmentStop switch Cutting attachment guard Vibration damping systemQuick release MufflerCutting equipment Locking nutSharpening the saw blade Cutting equipmentSharpening grass cutters and grass blades Trimmer head Fitting the handlebar 235R, 235FR AssemblyFitting the handlebar 232R Fitting a blade guard, grass blade and grass cutter 232R Transport position, handlebarAssembling the cutting equipment Fitting the blade guard and saw blade 232R Fitting the blade guard and saw blade 235R, 235FR Fitting other guards and cutting attachments 232R AM LAdjusting the harness and clearing saw Spreading the load on your shouldersCorrect height Correct balanceFuel Fuel safetyFuel Handling Fueling MixingStarting and Stopping Check before startingStarting and stopping Cold engineStarting StoppingBasic safety rules Working TechniquesGeneral working instructions ABC of clearingForestry clearing using a saw blade Working methodsGrass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingMaintenance CarburetorHigh speed jet H Correctly adjusted carburetorMuffler Cleaning the air filter Cooling systemBevel gear Air filterSpark plug Maintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataTechnical Data Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsSuper Auto Super Auto II Page T35 Trimmy Hit Trimmy Hit Pro Trimmy SII Page S35 ´z+R9¶5*¨ T45 1150255-95 ´z+R9¶5*¨ ´z+R9¶5*¨
Top Page Image Contents