Mufﬂer, High speed jet H | Husqvarna 325HE3 specification

MAINTENANCE

The blades must also remain stationary when the choke control is in the start throttle position.

IMPORTANT! If the idle speed cannot be adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

High speed jet H

The high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H is set too lean (screwed in too far) the engine speed will be too high and cause engine damage. Do not let the engine run at full speed for more than 10 seconds.

Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down. Then turn the high speed jet H very slowly anticlockwise until the engine starts to run unevenly. Now turn the high speed jet H slowly clockwise a little way until the engine runs smoothly.

Note that the engine should not be under load when you adjust the high speed jet H. You should therefore remove the cutting attachment, nut, support ﬂange and drive disc before adjusting the high speed jet H. The high speed jet H is adjusted correctly when the machine burbles a little. If the machine races then the setting is too lean. If the engine produces a lot of smoke and burbles a lot then the setting is too rich.

CAUTION! For optimum adjustment of the carburettor, contact a qualiﬁed dealer/service workshop that has a revolution counter at their disposal.

Correctly adjusted carburettor

When the carburettor is correctly adjusted the machine accelerates without hesitation and burbles a little at maximum speed. It is also important that the blades do not move when the engine is idling or when the choke control is in the start position. If the low speed jet L is set too lean it may cause starting difﬁculties and poor acceleration.

If the high speed jet H is set too lean it will result in less power, less performance, poor acceleration and/or damage to the engine. If both the L and H jets are set too rich it will results in acceleration problems or too low a working speed.

Mufﬂer

CAUTION! Some mufﬂers are ﬁtted with a catalytic converter. See chapter on Technical data to see whether your machine is ﬁtted with a catalytic converter.

The mufﬂer is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause ﬁre if directed against dry and combustible material.

Some mufﬂers are equipped with a special spark arrestor mesh. If your machine has this type of mufﬂer, you should clean the mesh at least once a week. This is best done with a wire brush.

On mufﬂers without a catalytic converter the mesh should be cleaned weekly, or replaced if necessary. On mufﬂers ﬁtted with a catalytic converter the mesh should be checked, and if necessary cleaned, monthly. If the mesh is damaged it should be replaced. If the mesh is frequently blocked, this can be a sign that the performance of the catalytic converter is impaired. Contact your dealer to inspect the mufﬂer. A blocked mesh will cause the machine to overheat and result in damage to the cylinder and piston. See also instructions under the heading Maintenance.

CAUTION! Never use a machine with a defective mufﬂer.

WARNING! Mufﬂers ﬁtted with catalytic

!converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember the risk of ﬁre!

English – 17

325HE3 specifications

The Husqvarna 325HE3 is an advanced, reliable, and versatile professional hedge trimmer designed for both efficiency and comfort. This robust tool is well-suited for landscapers, gardeners, and maintenance professionals who require powerful performance in various trimming and shaping tasks.

One of the key features of the 325HE3 is its powerful 25.4cc X-Torq engine. This engine technology ensures maximum power output while minimizing fuel consumption and exhaust emissions. This makes the trimmer not only environmentally friendly but also cost-effective for prolonged use. The lightweight design of the engine contributes to lower overall weight, enhancing maneuverability during operation.

The Husqvarna 325HE3 boasts a unique articulated cutting head with a 135-degree range of adjustment. This allows for precise cutting at various angles, ensuring that users can reach tight spots and trim hedges effectively without straining their bodies. The cutting blades are double-sided and are constructed from hardened steel, providing long-lasting sharpness and durability while minimizing wear and tear.

Comfort is a major consideration in the design of the 325HE3. It features a cushioned rear handle and an ergonomic front handle that allows for a firm grip and reduces vibration during use. This ergonomic design helps reduce operator fatigue, enabling longer periods of operation without discomfort. The trimmer also comes equipped with a protective blade cover that ensures safety during storage and transport.

In addition, the Husqvarna 325HE3 incorporates advanced technologies such as LowVib, which minimizes vibrations during operation, contributing to user comfort and reducing the risk of long-term injuries. The air filtration system is designed to prolong engine life and enhance performance by keeping the airflow clean and efficient.

The ease of maintenance is also a highlight of the Husqvarna 325HE3. The easily accessible components allow for quick inspections and servicing, making it user-friendly for people seeking to keep their equipment in top condition.

Overall, the Husqvarna 325HE3 is a professional-grade hedge trimmer that seamlessly combines power, ergonomics, and advanced features, making it a preferred choice for those who demand excellence in their landscaping tools. Whether for commercial use or personal gardening projects, it stands out as a reliable companion for all trimming needs.