Troy-Bilt 52051, 52052 Never run the engine inside a closed area, At top of debris shield brace

Page 5

Section 1: Safety

2.Never run the engine inside a closed area.

3.Never clean, make adjustments or repairs with the engine running. Disconnect the spark plug wire and keep the wire away from the plug to prevent accidental starting. Remove key on electric start models.

4.Keep all nuts and bolts tight, espe- cially the trimmer head attachment bolts, and keep equipment in good condition. Check mounting hardware on trimmer head every time you change trimmer line and prior to each use.

5.Never tamper with safety devices. Check their proper operation regularly.

6.To reduce fire hazard, keep mower free of grass, leaves or other debris build-up. Clean up oil or fuel spills. Let machine cool before storing.

7.After striking an object, stop the engine and disconnect the spark plug wire. Inspect the trimmer/mower and repair, if necessary, before restarting.

8.Never make adjustments or repairs while engine is running.

9.Components subject to wear, damage and deterioration could ex- pose moving parts or allow objects to be thrown. Frequently check compo- nents and replace with factory recom- mended parts, when necessary. Regularly inspect the trimmer head

and debris shield. Make sure they are not bent, damaged, or loose.

10.Only use eighteen-inch long .130" or .155" diameter trimmer line. Never use other lengths, diameters or material as trimmer line.

11.Trimmer line moves at high speed and can cut. Always

stop the engine and let all moving parts stop before replacing the trimmer lines. Let the engine cool.

12.Do not change the engine gover- nor setting or overspeed the engine. The governor controls maximum safe operating speed and protects the en- gine and all moving parts from dam- age caused by overspeed. Authorized service shall be sought if a problem exists.

13.Do not touch engine parts which may be hot from operation. Allow parts to cool completely before in- specting, cleaning or repairing the unit.

14.Maintain or replace safety and in- structional decals. Refer to the sepa- rate Parts Catalog for replacement decal information.

15.For units equipped with electric start:

a)Batteries produce explosive gases. Keep sparks, flame,

cigarettes, etc., away. Venti- late the area when charging the battery. Do not charge the battery in an airtight space.

b)Do not use a battery charger other than the one provided to you.

c)The battery contains toxic ma- terials. Do not damage the battery case. If the case is bro- ken or damaged, avoid contact with the battery contents.

d)Properly dispose of a dam- aged or worn out battery. Check with local authorities for proper disposal methods.

e)Do not short circuit the bat- tery. Severe burns and fire can result.

16.Use only original-equipment re- placement parts. Parts manufactured by others could present safety hazards and affect performance even though they may fit on this trimmer/mower.

17.Remember– the end of the season is a good time to inspect equipment prior to storage.

18.To guard against engine overheat- ing, always have the engine debris filter mounted and clean.

CAUTION

Read Owner's Manual before operating this machine. If you need a replacement manual, write to the address listed on the serial number decal on this unit.

ROTATING CUTTING HEAD

Do not service or adjust cutting head or other moving parts unless engine is stopped and spark plug wire is disconnected.

Keep trimmer head, foam debris guard, deck and other surface areas clean. Before cleaning, shut off engine and disconnect spark plug.

IMPORTANT: Do not operate this machine with debris shield open.

At top of clear plastic shield facing operator

On left

handlebar

Safety Decals

Make certain that all safety decals on this equipment are kept clean and in good condition. The decals are shown (at reduced sizes) below. If you need a re- placement decal, please refer to the Parts List in this Manual.

SEE SAFETY INSTRUCTIONS UNDER DEBRIS SHIELD

To open, pull up debris shield, then tip forward.

At top of debris shield brace

WARNING

THROWN OBJECT HAZARD

Objects such as rocks, pebbles and small debris will be thrown violently by the cutting head, resulting in significant hazard to eyes and exposed body parts!

Keep children, pets and bystanders 50 feet away from machine while operating.

Be alert to hidden obstacles.

ROTATING CUTTING HEAD

Do not service or adjust cutting head or other moving parts unless engine is stopped and spark plug wire is disconnected.

1904403 (1/97)

At front of deck

WARNING

THROWN OBJECT HAZARD

Wear eye protection!

Objects can be thrown up to 50 feet!

Be alert to hidden obstacles!

At rear of deck

housing on left side

DANGER

KEEP HANDS and FEET AWAY

At rear of deck housing

At front of deck

 

on right side

 

3

Image 5
Contents Recoil Start Model Shown Trimmer/MowerSee Back Cover for Customer Service Information Remove the key on electric start models SafetyDo not put Use this equipment for its intended purpose only Watch for traffic when near or when crossing roadwaysDo not At rear of deck Housing on left side Never make adjustments or repairs while engine is runningNever run the engine inside a closed area At top of debris shield braceIntroduction AssemblyAdd Motor Oil Engine CONTROLS/FEATURES Features and ControlsUse this lever F, -1 to regulate engine speed Recoil starter H, -1 is mounted on the engineAdjust Handlebar Height PRE-START ChecklistOperation IntroductionAdjust Line Cutting Height Using the Trimmer Head Control BailTough trimming conditions, use the highest height settings General RecommendationsMer/mower Recoil Start ModelElectric Start Model Trimming & Mowing Techniques and Tips Vary the Throttle Setting to Suit the JobUse the Right Diameter Line for the Trimming Job Be alert to hidden obstacles100 Maintenance/RepairsRequired Maintenance Schedule Securely Adjusting Trimmer Head EngagementRemoving & Replacing the Trimmer Head Belt Inspection Belt ReplacementInspecting / Replacing the Drive Belt Cleaning and Debris Removal Belt Performance TroubleshootingTo Change Trimmer Lines Changing Trimmer Mower LinesRepeat steps 2 through 5 to replace the second trimmer line DirectionGeneral Engine Maintenance Cleaning the Engine Foam Debris FilterGeneral Lubrication Compact StorageBattery Replacement Battery RechargingEngine does not start Problem Possible Cause CorrectionParts Ordering Information Trimmer/Mower Parts List Ref. # Description Qty Ref. # DescriptionHandlebar Assembly Spindle Plate Assembly Lower Steering Assembly Description Qty Trim Head AssemblyCustomer Service and Technical Service Warranty ServiceReplacement Parts Engine Service and Repair

52051, 52052 specifications

Troy-Bilt has long been recognized for its commitment to quality and innovation in outdoor power equipment, and the Troy-Bilt 52052 and 52051 models are no exception. These garden tillers are designed to tackle a variety of tilling tasks, making them suitable for both novice gardeners and seasoned horticulturists.

The Troy-Bilt 52052 features a robust 4-cycle engine, which provides ample power to tackle tough soil conditions. With a displacement of 196 cc, this model is equipped to till soil up to 10 inches deep, ensuring that nutrients can be effectively mixed into your garden bed. The 52051 shares similar characteristics but is tailored for slightly different gardening needs. Both models feature an adjustable tilling width, allowing users to customize their tilling experience, with widths ranging from 16 to 21 inches. This versatility enables gardeners to efficiently navigate tight spaces or cover larger plots in fewer passes.

One of the standout technologies integrated into these models is the "Rear-Tine" design, which allows for smoother operation and superior maneuverability. This design feature not only enhances ease of use but also reduces strain on the user, making gardening tasks less daunting. The counter-rotating tines of the tillers are specifically designed to break up hard soil, allowing for effective aeration and preparation of planting beds.

Both models excel in terms of convenience, featuring a user-friendly starting system. The push-button electric start on the 52052 is particularly beneficial for those who may have difficulty with traditional pull-start mechanisms. Additionally, the tillers are designed with ergonomic controls, ensuring that users can operate them comfortably for extended periods.

Durability is another hallmark of the Troy-Bilt brand, and these tillers are constructed with high-quality materials to withstand the rigors of regular use. The heavy-duty steel tines are built to last, and the sturdy frame ensures stability while in operation.

In summary, the Troy-Bilt 52052 and 52051 garden tillers combine power, versatility, and user-friendly features, making them excellent choices for anyone looking to enhance their gardening experience. With their advanced technologies and robust construction, these tillers promise to deliver outstanding performance for all your gardening needs.