USER REPLACEABLE SERVICE PARTS
REPLACEMENT PART
Container of Replacement Line
Assist Handle
Bolt Carriage,
Wing Nut
Shield Assembly
Edge Guide
'_ WARNING: Perform the following steps after each use.
•Stopthe unit and disconnect the pow- er source when not in use.
•Carry the unit with motor stopped.
•Store the unit so the line limiter blade cannot cause injury.
PART NUMBER
530403805
530403886
530016152
530404393
530403845
•Store unit and extension cord indoors
in a high, dry place out of the reach of children. Store unit unplugged.
•Store unit with all guards in place. Position unit so that any sharp object cannot accidentally cause injury.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from tile power source before performing all of the recommended remedies below except remedies that re- quire unit to be operating.
TROUBLE |
|
| CAUSE |
|
|
|
|
|
| REMEDY |
|
|
|
|
| ||||
1. Crowdh_g | line | against | 1. | Allow | tip of Ih_eto do the cutth_g. | ||||||||||||||
stops | under | a |
| material |
| being | cut. |
|
|
|
|
|
|
| |||||
load | or | does | not | 2. Electrical | failure. |
| 2. | Contact | Sears | Service | (see back | ||||||||
turn | when | switch |
|
|
|
|
|
|
|
|
| cover). |
|
|
|
|
| ||
is pressed. |
|
| 3. Thrown | circuit | breaker. | 3. | Check | breaker | box. |
| |||||||||
|
|
|
|
| 4. | Debris | stopping | head. | 4. | Remove | debris. |
|
| ||||||
Line | breaks |
|
| 1. | Line | improperly |
| routed | 1. | Check | line | routing. |
| ||||||
while | cutting, |
| in head. |
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
| 2. | Incorrect | line | size | 2. | Use only | 0.080 | inch (2 mm) dia. line. | |||||||
|
|
|
|
| 3. | Dirt | on | unit. | 3. | Clean | unit. |
|
|
| |||||
Line | welds | onto | 1. | Line | size | is | incorrect. | 1. | Use only 0.080 inch (2 ram) dia. line. | ||||||||||
cutting | head. |
| 2. | Crowding | line | against | 2. | Allow | tip of | line | to do the | cutting. | |||||||
|
|
|
|
|
| material |
| being | cut. |
|
|
|
|
|
|
| |||
Line | usage |
| is | 1. Line | improperly |
| routed | 1. | Check | line | routing. |
| |||||||
excessive, |
|
|
| in head. |
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
| 2. | Line | size | is | incorrect. | 2. | Use only | 0.080 | inch (2 mm) dia. line. | ||||||
|
|
|
|
| 3. | Crowding | line | against | 3. | Allow | tip | of | line | to do the cutting. | |||||
|
|
|
|
|
| material |
| being | cut. |
|
|
|
|
|
|
| |||
|
|
|
|
| 4. | Cutting | head | worn or | 4. | Contact | Sears | Service | (see back | ||||||
|
|
|
|
|
| damaged, |
|
|
|
|
| cover). |
|
|
|
|
| ||
lO