Bolens BL150 manual Install and Adjust the D-HANDLE, Installing the Cutting Shield

Page 7

INSTALL AND ADJUST THE D-HANDLE

3.

The squared boHthoHein the handHe is to the right.

2.Insert the shouHder boHtinto the squared hoHein the handHeand push through, On the Heftside of the handHe, pHacethe washer on the boHt,then screw the wing nut onto the boHt.Do not tighten untiHyou make the handHeadjustment.

3.Rotate the D-handHe to pHacethe grip above the top of the shaft housing, Mace it a minimum of 6 inches (15.24 cm) from the end of the shaft grip.

/Shaft Grip

__

Shaft Hous ,rig

_ DoHandle

1.__ Tighten

Bolt-------

_f

v

F_g.1

4.While holding the unit in the operating position (Fig, 2), position the D-handJe to the Jocation that provides you the best grip.

Tighten the wing nut untiJ the D-handJe is secure.

INSTALLING THE CUTTING SHIELD

Use the following instructions if the cutting attachment

shield on your unit is not installed or if you ever need to re- install it,

WARNING: Toprevent serious

personal injury,

never operate the trimmer without the cutting attachment shield in place.

[nstammon a Straight Shaft (BL150)

1.SHidethe cutting attachment shieHdinto the shieHd mount on the cutting attachment, AHignthe screw holes in the shield with the holes in the cutting attachment shieHdmount (Fig. 2).

2.Mace one of the three (3) suppHied hex Hocknuts into one of the three recessed holies on the top of the cutting attachment shieHd(Fig 3),

3.[nstaHH screw into the hoHefrom the bottom of the cutting attachment shieHd.Screw it into the nut instaHHed in step 2 untiHit is started (Fig 3). Do not tighten.

4.Repeat steps 2 and 3 untiHaHHthree screws have been started. Then tighten aHHscrews secureHy with a PhiHHipshead screwdriver.

Shaft Housing

Cutting

 

Cutting

Attachment

 

 

Attachment

 

\

 

Shield

 

 

 

 

ShieJd

 

 

Mount

 

 

F_g. 2

_He×

Lock Nut

Recessed Homes

[nstammon a Curved Shaft (BL100)

1.Mace the cutting attachment shieHdonto the shaft housing, Be sure the guard mounting bracket sHides into the shoton the edge of the cutting shieHd.Rotate the shieHdinto pHace,countercHockwise (Fig, 4). The holies in the guard mounting bracket and cutting attachment shieHdwill[[ine up.

2.From inside the cutting attachment shieHd, push the square boHtthrough the hoHeunti[ the threaded end protrudes through the guard mounting bracket (Fig, 5),

3.Put the washer on the boHt,then screw the wing nut onto the boHtand tighten.

Sha_ Housing_

Guard

Mounting

Bracket

Cutting Attachment

Shield

F_g. 4

Guard

Mounting \

Bracket

FTV_

• •

\

Wing Nut

Square Bolt

F_g.5

Image 7
Contents BL100 BL150 Cycle Gas Trimmers Product Contains Chemicals ContentsThank YOU Spark Arrestor NoteFor QUESTIONS, Call 1o800o520o5520 Safety Warnings for GAS TrimmersSymbol Meaning Safetywarning canWHmLE OPERATmNG Other Safety WARNmNGSAlwaysuse clean,freshunleadedfuel Primer Bumb AppucatonsInstalling the Cutting Shield Install and Adjust the D-HANDLELiter Using Bmended FuemsUnleaded GAS 2FL OZStarting Position Starting InstructionsHolding the Trimmer Frequency Mnntenance MAmNTENANCESchedule UNE mNSTALLATmONForUsewithSingme MNSTALUNG a Prewound Reel AIR Filter MaintenanceRemoving the Air Filter/Muffler Cover Carburetor Adjustment Spark Arrestor MaintenanceReplacing the Spark Plug Transporting CleaningStorage Long Term StorageFillfueHtankwithpropedymixed fueH ReplaceorcleantheairfilterRPM Air-CooHed,2-CycleCalifornia / EPA Emission ControJ Warranty Statement You Manufacturers Limited Warranty for