Snapper LT-200 Series manual Leveling The Mower, 1/2 Max High cut, Lift Rod

Page 35

Troubleshooting, Adjustment, & Service

WARNING

Before checking mower, shut off PTO and engine, remove the key, and allow all moving parts to stop.

Leveling The Mower

If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut. Make sure tire pressure is correct as specified in Checking Tire Pressure.

3/8” - 1/2”

A

max in

 

high cut

 

 

B

SIDE-TO-SIDE LEVELING

Figure 39. Leveling The Mower Side-to-Side

1.

With the mower installed, place the tractor on a

A. Lift Rod

 

smooth, level surface such as a concrete floor. Turn

B. Locknut

 

the front wheels straight forward.

 

2.

Check for bent blades and replace if necessary.

 

 

3. Place the mower in mid-cut position. Arrange the outside mower blades so that they are pointing from side-to-side.

4.

Measure the distance between the outside tips of

B

 

each blade and the ground. If there is more than 1/8”

 

 

 

(3mm) difference between the measurements on

B

 

each side, proceed to step 5. If the difference is 1/8”

 

 

(3mm) or less, proceed to step 6.

A

5.

Turn the locknut (B, Figure 39) to raise or lower that

A

 

side of the mower.

Note: The maximum the mower can be adjusted in high cut is 3/8” to 1/2” between the frame and mower up-stop. See Figure 39.

FRONT-TO-BACK LEVELING

6.Arrange the blades so they face front-to-back.

7.Measure the distance from the ground to the front tip of the center blade, and from the ground to rear tips of left-hand and right-hand blades.

Figure 40. Leveling The Mower Side-to-Side

A.Locknuts

B.Spacers

44” MOWER DECK -

Front tip of the center blade should be 1/4" (6mm) higher than rear tips of left-hand and right-hand blades. If not, proceed with step 8.

38” & 40” MOWER DECKS -

A front to back deck height variance of 1/8” (3mm) and side to side variance of 1/8” (3mm) is acceptable. If not, proceed with step 8.

8.To raise front of mower deck, tighten locknuts (A, Figure 40) and against spacers (B). To lower front of mower deck, loosen locknuts (A). Locknuts must be turned evenly on both sides to keep deck level.

9.Re-check the blade measurement then tighten the front nut (B) against the bracket to secure.

33

Page 34 Page 36
Image 35
Page 34 Page 36
Contents 1734103 18.5HP Hydro Tractors Mower DecksMower Decks 20HP Hydro Tractors Page Table of Contents Safety Rules & Information Operating Safety Slope Operation Safety Rules and InformationGeneral Operation Safety Rules & InformationIgnition System Safe Handling of Gasoline Service & MaintenanceTractor ID Tag Mower ID Tag Identification NumbersCE Identification Tag Markings Safety Icons Safety DecalsSafety Decals Fuel Level Transmission Release Attachment Lift CE Safety IconsDecals Locations 38, 40 & 44 Mowers OnlyHeadlights Control FunctionsThrottle Control ChokeFeatures & Controls Hourmeter Volt Power OutletParking Brake Function Cruise Control OperationStarting The Engine General Operating SafetyOperational Safety Checks Adding FuelOperating the Tractor Muffler and surrounding areas may be hot Mower Deck Removal & InstallationInstalling the Mower Deck Removing the Mower DeckStorage Adjusting Mower Cutting HeightAttaching a Trailer Size Check Tire PressuresBefore Every Spring Each Hours 100 250 Fall Use Before Every Spring Each Hours 100 Fall UseEngine Maintenance Battery Maintenance Regular MaintenanceSafety Interlock System Check PTO Clutch Adjustment CheckTransmission Identification Transmission MaintenanceHood Removal and Installation K46 MaintenanceGrease Service Interval Every 25 HoursLubrication OilLubricate Rear Axle Shafts Service Interval YearlyServicing the Mower Blades Service Interval Every 100 Hours or As RequiredCheck & Fill Engine Oil Closed ValveOpen Air Filter Service Air Filter Removal & InstallationPre-Cleaner Service Briggs & Stratton Single Cylinder Models Replace Spark Plug Troubleshooting Troubleshooting Adjustment, & ServiceTroubleshooting the Mower Brake Adjustment Troubleshooting, Adjustment, & ServiceSeat Adjustment Battery ChargingAdjust PTO Clutch Window Adjustment Nut Feeler Gauge PTO clutch adjustmentGauge Wheels Select Models Fuse ReplacementMower Adjustments Lift Rod Leveling The Mower1/2 Max High cut To avoid damaging belts, do not PRY Mower Belt ReplacementK46 20 HP* Briggs & Stratton18.5 HP* Briggs & Stratton LT SeriesTechnical Manuals Replacement PartsMaintenance Items

LT-200 Series specifications

The Snapper LT-200 Series is an advanced riding mower designed to deliver an exceptional mowing experience, combining user-friendly features with powerful performance. This series is specifically engineered for homeowners who require both efficiency and reliability in their lawn care routine.

One of the primary features of the Snapper LT-200 Series is its powerful engine. Equipped with a robust Briggs & Stratton engine, the LT-200 is designed to provide significant horsepower, ensuring that it can handle various grass types and challenging terrains with ease. The engine is also designed for fuel efficiency, which means users can maintain their lawns without excessive fuel consumption.

A standout feature of the LT-200 Series is its cutting system. The mower features a 42-inch cutting deck, which allows for wider mowing coverage in fewer passes, saving both time and energy. The deck is adjustable, enabling users to choose from multiple cutting heights, ensuring that they can achieve the desired lawn length. The mulching capability is another highlight, allowing users to finely chop grass clippings to distribute nutrients back into the soil, promoting a healthier lawn.

Comfort is a significant focus in the Snapper LT-200 design. The mower features a plush, high-back seat with armrests to provide support during extended mowing sessions. The easy-to-use control panel is intuitively designed, giving users quick access to throttle, drive engagement, and mowing functions, simplifying the mowing process regardless of the user’s experience level.

In terms of maneuverability, the LT-200 Series boasts a tight turning radius, allowing it to navigate around trees, flowerbeds, and other obstacles with ease. The six-speed transmission provides smooth shifts that enable users to tailor their speed according to the terrain, whether it's flat or hilly.

Additionally, the Snapper LT-200 incorporates advanced technologies like the SureStart engine technology, ensuring reliable startup on the first try, and a durable steel frame construction, contributing to the mower's longevity and robustness. With easy access to maintenance points, regular upkeep becomes a hassle-free task.

Overall, the Snapper LT-200 Series stands out as a comprehensive solution for homeowners looking for a reliable riding mower that combines power, comfort, and advanced features, making lawn care an enjoyable experience rather than a chore.
Top Page Image Contents