Snapper Lawn Mower Oil Change & Oil Capacity Guide
Page 26

Regular Maintenance

Oil Drain Valve Operation

1.Place a suitable container with a 4 quart capacity under the oil drain valve (A, Figure 22 or 23).

2.Loosen or remove the dip stick (C, Figure 22 or 23).

3.Wipe oil drain valve (B, Figure 24) and cover (C) with paper towel or rag.

NOTE: Sliding a hose with a 1/2” (12.5 mm) inside diameter tube over the valve nipple may aid in guiding the draining oil.

4.Rotate the drain valve (B) counter clockwise and pull out 1/4” (6.35 mm) for engine oil to drain. Allow ample time for complete drainage.

5.After all the oil has drained, close the oil drain valve

(B) by pushing in and rotating clockwise to close.

6.Wipe the nipple (D) with paper towel or rag. Install the cover (C) over nipple (D).

A

 

A

 

 

 

B

B

 

 

 

 

D

Valve

 

Valve

 

Open

Closed

C

C

 

 

Figure 24. Oil Drain Valve

A.Engine Block / Valve Base

B.Oil Drain Valve

C.Cover

D.Nipple

Change Engine Oil

BRIGGS & STRATTON MODELS

Service Interval: 50 hours or once per season.

Oil Capacity: Approximately1-7/8 quarts (1.8L) without filter change.

NOTE: Change engine oil while the engine is warm. Run the engine for a few minutes, then shut the engine off and allow it to cool from hot to warm.

1.Clean the area around the dip stick (C, Figure 22 or 23) and oil drain valve (A).

2.Drain engine oil. See OIL DRAIN VALVE OPERATION above.

3.Fill the crankcase with oil. See CHECK ENGINE OIL LEVEL.

Change Engine Oil & Filter

BRIGGS & STRATTON MODELS

Service Interval: 100 hours or once per season.

Oil Capacity: Approximately 2 quarts (1.9L) with oil filter change.

NOTE: Change engine oil while the engine is warm. Run the engine for a few minutes, then shut the engine off and allow it to cool from hot to warm.

1.Clean the area around the dip stick (C, Figure 22 or 23) and oil drain valve (A).

2.Drain engine oil. See OIL DRAIN VALVE OPERATION above.

3.Remove the oil filter (B). Discard the filter.

4.Using a drop of oil on your finger tip, wet the rubber gasket on the bottom of the new filter.

Use oil classified API Service Class SF, SG, SH, SJ or better with SAE Viscosity:

 

 

 

 

 

 

30 Conventional**

 

 

 

 

5W-30

 

 

 

 

 

 

 

10W-30

 

 

 

 

 

 

Conventional*

 

 

 

 

 

 

Synthetic 5W-30, 10W-30

 

 

˚F

-20

0

20

32

40

60

80

100

˚C

-30

-18

-7

0

4

16

27

38

*CAUTION: Air cooled engines run hotter than automotive engines. The use of non-synthetic multi-viscosity oils (5W-30, 10W-30, etc.) in temperatures above 40º F (4ºC) will result in higher than normal oil consumption. When using a multi-viscosity oil, check oil level more frequently.

**CAUTION: SAE 30 oil, if used below 40º F (4ºC), will result in hard starting and possible engine bore damage due to inadequate lubrication.

Figure 25. Recommended Engine Oil -

Briggs & Stratton Models

5.Turn the filter clockwise until the rubber gasket meets the filter base. Then turn 1/2 to 3/4 turn more.

6.Fill the crankcase with oil. See CHECK ENGINE OIL LEVEL.

7.Test run the engine to check for leaks. Stop the engine for 1 minute, then recheck the oil level.

24

Page 25 Page 27
Image 26
Page 25 Page 27
Contents 1734103 18.5HP Hydro Tractors Mower DecksMower Decks 20HP Hydro Tractors Page Table of Contents Safety Rules & Information Operating Safety Safety Rules and Information Slope OperationSafety Rules & Information General OperationIgnition System Service & Maintenance Safe Handling of GasolineTractor ID Tag Mower ID Tag Identification NumbersCE Identification Tag Markings Safety Icons Safety DecalsSafety Decals 38, 40 & 44 Mowers Only CE Safety IconsDecals Locations Fuel Level Transmission Release Attachment LiftChoke Control FunctionsThrottle Control HeadlightsFeatures & Controls Cruise Control Operation Volt Power OutletParking Brake Function HourmeterAdding Fuel General Operating SafetyOperational Safety Checks Starting The EngineOperating the Tractor Removing the Mower Deck Mower Deck Removal & InstallationInstalling the Mower Deck Muffler and surrounding areas may be hotStorage Adjusting Mower Cutting HeightAttaching a Trailer Before Every Spring Each Hours 100 Fall Use Check Tire PressuresBefore Every Spring Each Hours 100 250 Fall Use SizePTO Clutch Adjustment Check Regular MaintenanceSafety Interlock System Check Engine Maintenance Battery MaintenanceK46 Maintenance Transmission MaintenanceHood Removal and Installation Transmission IdentificationOil Service Interval Every 25 HoursLubrication GreaseService Interval Yearly Lubricate Rear Axle ShaftsService Interval Every 100 Hours or As Required Servicing the Mower BladesCheck & Fill Engine Oil Closed ValveOpen Air Filter Service Air Filter Removal & InstallationPre-Cleaner Service Briggs & Stratton Single Cylinder Models Replace Spark Plug Troubleshooting Adjustment, & Service TroubleshootingTroubleshooting the Mower Battery Charging Troubleshooting, Adjustment, & ServiceSeat Adjustment Brake AdjustmentPTO clutch adjustment Adjust PTO Clutch Window Adjustment Nut Feeler GaugeGauge Wheels Select Models Fuse ReplacementMower Adjustments Lift Rod Leveling The Mower1/2 Max High cut Mower Belt Replacement To avoid damaging belts, do not PRYLT Series 20 HP* Briggs & Stratton18.5 HP* Briggs & Stratton K46Technical Manuals Replacement PartsMaintenance Items

LT-200 Series specifications

The Snapper LT-200 Series is an advanced riding mower designed to deliver an exceptional mowing experience, combining user-friendly features with powerful performance. This series is specifically engineered for homeowners who require both efficiency and reliability in their lawn care routine.

One of the primary features of the Snapper LT-200 Series is its powerful engine. Equipped with a robust Briggs & Stratton engine, the LT-200 is designed to provide significant horsepower, ensuring that it can handle various grass types and challenging terrains with ease. The engine is also designed for fuel efficiency, which means users can maintain their lawns without excessive fuel consumption.

A standout feature of the LT-200 Series is its cutting system. The mower features a 42-inch cutting deck, which allows for wider mowing coverage in fewer passes, saving both time and energy. The deck is adjustable, enabling users to choose from multiple cutting heights, ensuring that they can achieve the desired lawn length. The mulching capability is another highlight, allowing users to finely chop grass clippings to distribute nutrients back into the soil, promoting a healthier lawn.

Comfort is a significant focus in the Snapper LT-200 design. The mower features a plush, high-back seat with armrests to provide support during extended mowing sessions. The easy-to-use control panel is intuitively designed, giving users quick access to throttle, drive engagement, and mowing functions, simplifying the mowing process regardless of the user’s experience level.

In terms of maneuverability, the LT-200 Series boasts a tight turning radius, allowing it to navigate around trees, flowerbeds, and other obstacles with ease. The six-speed transmission provides smooth shifts that enable users to tailor their speed according to the terrain, whether it's flat or hilly.

Additionally, the Snapper LT-200 incorporates advanced technologies like the SureStart engine technology, ensuring reliable startup on the first try, and a durable steel frame construction, contributing to the mower's longevity and robustness. With easy access to maintenance points, regular upkeep becomes a hassle-free task.

Overall, the Snapper LT-200 Series stands out as a comprehensive solution for homeowners looking for a reliable riding mower that combines power, comfort, and advanced features, making lawn care an enjoyable experience rather than a chore.
Top Page Image Contents