Snapper EZF6100M, EZF2100DKU, EZF2300GKU, EZF5200M Annually END of Each Season, From previous

Page 17

Section 3 - MAINTENANCE

3.5ANNUALLY (END OF EACH SEASON)

(Continued from previous Page)

3.5.2.FUEL FILTER (DIESEL ENGINE ONLY)

Service fuel filter as instructed in engine owner’s manual. Turn key to “OFF” position. Engine MUST be stopped and MUST be cold before removing filter.

1.Move the fuel filter cock handle to the closed position.

2.Remove the fuel filter bowl retaining ring. Fuel filter bowl, two “O” Rings, spring and filter can be removed. See Figure 3.8.

3.Replace filter element. Clean filter bowl with fresh diesel fuel. Reassemble the fuel filter bowl assembly. Tighten retaining ring securely. Check for leakage. Air bleed the fuel system.

4.Fill the fuel tank to the fullest extent. Open the fuel filter cock.

5.Loosen air vent plug a few turns at the top of fuel filter/fuel cock assembly. Allow air bubbles to be released. Close air vent plug when a steady flow of fuel is observed.

NOTE: After replacing fuel filter, engine may have to be cranked briefly with air vent plug loosened to purge all air from system.

3.6DECK REMOVAL

Move machine to an area where the mower deck is to be disconnected. Turn engine “OFF” but leave key switch in the “ON” position. Engage parking brake.

1.The rear of deck must be raised up and both jack stands moved down to the lowest position and both locking pins inserted. NOTE: Jack stands are stored on the left and right rear sides of the mower.

2.Using deck lift switch, lower deck down to rest on jack stands.

3.The hitch latch pins are shown in the latched position. The latched position locks the deck lift arm into position. See Figure 3.9.

HITCH LATCH PIN

SHOWN IN LATCHED

OR LOCKED

POSITION

AIR VENT

PLUG

FUEL COCK

SMALL “O”

RING

FUEL FILTER

SPRING

LARGE “O”

RING

FUEL BOWL

RETAINING

RING

FIGURE 3.8

DECK

LIFT ARMHITCH

PLATE

FIGURE 3.9

(Continued on Next Page)

WARNING

Allow engine to cool for at least ten minutes before performing service or maintenance. DO NOT smoke near fuel components when performing service or maintenance. DO NOT perform service and maintenance near an open flame. Wipe off any spilled fuel before starting engine. DO NOT run engine indoors.

17

Image 17
Contents Instruction No -4370 I.R /6/01 Model Number ExplanationPreparation Protection for ChildrenProtection Against Tipovers Mount and dismount machine from left side MaintenanceOperation Table of Contents Nomenclature IntroductionEngine Stop OFF RUN on Start Glow Plug PRE-HEAT SymbolsDiesel Fuel only Symbols PRE-START Check List Operating InstructionsStarting & Stopping ENGINE, Blades & Parking Brake Starting EngineStopping Engine Starting Engine from previousEngine Starting Mower BladesParking Brake Cutting Height AdjustmentOperation Motion Control Driving Machine Check Mower Blade Service After First 5 HoursChange Engine OIL Mower Components Check Mower Drive BeltAfter Every 25 Operating Hours Before Operating Mower Riding Mower LubricationOther Lubrication Points From previous Annually END of Each SeasonFuel Filter Diesel Engine only Deck RemovalPower Transfer Shaft Removal Neutral Position Adjustments Adjustments & RepairParking Brake Adjustment Blade Sharpening Mower Blade ReplacementBlade Wear Limits from previous Mower Drive Belt Replacement Mower Drive BELT, Engine Belt & Hydro Pump Belt ReplacementMower Drive Belt Removal Engine Belt RemovalBattery Installation Battery Battery RemovalBattery Service On NextBattery Testing BatteryNEW Battery Preparation Do not OverfillRemove NUT Remove Belt From Spindle Remove Blade Bolt Problem Probable Cause Corrective Action TroubleshootingProblem Probable Cause Corrective Action MAINTENANCE/REPLACEMENT Parts Service ScheduleDisclaimer of Warranty Year Limited WarrantyPage Page OUT Front Z-RIDER Hydro Drive Series