Snapper HZS14331BVE, HZS14381BVE, HZS15421KVE, HZS15422KVE, HZS18482BVE Loss Of Traction

Page 22

TROUBLESHOOTING

PROBLEM

 

PROBABLE CAUSE

 

CORRECTIVE ACTION

Rider Will Not Move Or

1. Joystick in the neutral “N” position.

1. Place joystick in desired speed position.

Loss Of Traction

2. Roll release lever is in “ROLL” position.

2. Move roll release lever to the engaged position.

 

3.

Low transmission hydraulic oil level.

3.

Contact authorized SNAPPER dealer.

 

4.

Parking Brake engaged.

4.

Move parking brake to disengaged position..

 

5.

Traction drive belt requires replacement

5.

Replace traction drive belt.

Blade(s) Not Cutting

1. Blade engagement switch in the “OFF” position.

1. Move blade switch to the “ON” position.

 

2.

Clutch belt slipping.

2.

Replace clutch belt.

 

3.

Mower belt slipping.

3.

Replace mower belt.

 

4.

Electric clutch not functioning.

4.

Contact authorized SNAPPER dealer.

Cutting Grass

1. Uneven tire pressure.

1.

Bring to proper pressure.

Improperly

2. Cutting height too low or high.

2.

Adjust cutting height.

 

3.

Engine speed too slow.

3.

Move throttle control to “FAST” position.

 

4.

Forward speed too fast.

4.

Move joystick to a slower speed.

 

5.

Terraced cut, side to side.

5.

Adjust side to side level

 

6.

Excessive deck pitch, front to rear.

6.

Adjust front to rear pitch.

 

7.

Cutting blade(s) dull or damaged.

7.

Sharpen cutting edges or replace blade(s).

 

8.

Blade belt slipping.

8.

Replace blade belt.

 

9.

Check electric clutch.

9. Adjust to proper specifications. (33” Deck Only)

 

10. Check clutch belt.

10. Replace clutch belt.

Poor Grass Discharge

1. Engine speed too slow.

1.

Move throttle control to “FAST” position.

 

2.

Forward speed too fast.

2.

Move joystick to a slower speed.

 

3.

Grass is wet.

3.

Mow when grass is dry.

 

4.

Excessively worn or damaged blade(s).

4.

Service mower blade(s)

 

5.

Build up of grass clippings and debris under deck.

5. Clean deck.

 

6.

Improper blade(s) installed on deck.

6.

Install proper SNAPPER blades.

 

7.

Blade(s) installed improperly on deck.

7.

Install blades properly.

Battery Will Not Charge

1. Poor cable connections.

1.

Clean cables and battery terminals.

 

2.

Bad battery cell(s)

2.

Replace with new battery.

 

3.

Faulty alternator.

3.

Contact engine manufacturer’s dealer.

Oil Leaking

1. Leaking hose fittings, clamps or reservoir.

1.

Verify fittings and hose clamps are tight.

4.7. MAINTENANCE/REPLACEMENT PARTS

MAINTENANCE/REPLACEMENT PARTS

Engine Speed Control Cable (Briggs 14 HP)

2-4642

Engine Speed Control Cable (Kohler 15 HP)

3-6506

Engine Speed Control Cable (Kohler 18 HP)

4-2992

Choke Control Cable (Kohler 15 HP)

2-4185

Choke Control Cable (Kohler 18 HP)

2-4185

33” Cutter Deck Blade

3-4168

38” Cutter Deck Blade (2 Blades Required)

4-2998

42” Cutter Deck Blade (2 Blades Required)

2-6691

48” Cutter Deck Blade (3 Blades Required)

2-9247

33” Cutter Deck Belt (Electric Clutch to Cutting Deck)

3-5389

38” Cutter Deck Belt (Electric Clutch to Cutting Deck)

2-9308

42” Cutter Deck Belt (Electric Clutch to Cutting Deck)

3-6585

48” Cutter Deck Belt (Electric Clutch to Cutting Deck)

4-2997

Wheel Drive Belt (Engine to Hydro Transaxle)

4-1823

Wheel Drive Belt (Engine to Hydro Transaxle) (48” Deck Only)

4-1829

Mower Drive Belt (Engine to Electric Clutch)

2-9117

Mower Drive Belt (Engine to Electric Clutch) (48” Deck Only)

4-6997

Parts Manual for Yard Cruiser Series 1 & 2

06109

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Yard Cruiser Manual No -6352 REV , 8/23/99Important Safety Instructions Operation Table of Contents Introduction Left Console ViewRight Console View NomenclatureOperating Instructions PRE-START Check ListStarting & Operation Engine Electric Start On NextStopping Engine Manual StartMower Blade Wheel DriveCutting Height Adjustment Do not park machine on slopesCheck Mower Blade Service After First 5 HoursChange Engine OIL Single Blade DeckService Every 25 Operating Hours 3.3.1. Engine HZS Model Series 1 Footrest ShownMower Deck Linkage Lubrication Mower Components 5. Mower Blade Spindle LubricationImportant 48 Decks Only Yard Cruiser Lubrication 1. Front Wheel BearingsEngine Air Filter Oil Filter Engine Oil Transaxle Annually END of Each SeasonStorage OUT of Season Belt Replacement Engine Adjustments & RepairMower Drive Belt Adjustment Belt RemovalFront or Rear View of Deck Triple Blade Deck Mower Deck Adjustment LevelnessBlade Brake Adjustments & Repair Deck Shown Front or Rear View of DeckTwin Blade Deck Front to Rear Deck Pitch 33 DeckMower Blade REPAIR/REPLACEMENT 4.3.1. Blade Wear Limits Wheel Brake AdjustmentMower Deck Timing ROD Battery Installation 1. Slide battery into battery cradle Blade ReplacementBattery Battery Removal Blade SharpeningNEW Battery Preparation 1. Remove battery from carton Battery ServiceBattery Storage Battery TestingProblem Probable Cause Corrective Action Trouble Shooting on NextMAINTENANCE/REPLACEMENT Parts Loss Of Traction100 Service Performed EachUSE HRS Season Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Service Notes REV , 8/23/99 Manual No

HZS14331BVE, HZS14381BVE, HZS15421KVE, HZS15422KVE, HZS18482BVE specifications

Snapper is a recognized name in the outdoor power equipment industry, and its latest series of zero-turn mowers is no exception. The Snapper HZS14331BVE, HZS14381BVE, HZS15421KVE, HZS15422KVE, and HZS18482BVE models bring a host of powerful features, cutting-edge technologies, and user-friendly characteristics to enhance lawn care efficiency.

The HZS14331BVE model is equipped with a reliable 14.5 HP engine, offering a balance of power and fuel efficiency, making it excellent for homeowners with average-sized lawns. Its compact design enhances maneuverability, allowing users to navigate tight spaces with ease. The machine is built with a durable steel frame, ensuring longevity while providing stability on various terrains.

Following closely is the HZS14381BVE, which steps up with an 18 HP engine, providing that extra power for tackling more extensive lawns or tougher grass conditions. This model incorporates a 42-inch cutting deck, allowing for an efficient mowing experience. The deck’s design promotes optimum airflow, resulting in a cleaner cut and better grass dispersal.

The HZS15421KVE offers even more capability with a 21 HP engine. It emphasizes speed and precision, featuring a user-friendly hydrostatic transmission system that allows for easy control and a smooth driving experience. This model is particularly designed for homeowners wanting a machine that combines performance with comfort.

With the HZS15422KVE, users will see a significant upgrade in cutting width, with a robust 54-inch deck that can handle larger properties efficiently. Its comfortable seat and adjustable steering controls ensure that operators can mow for extended periods without fatigue. The model also includes a mulching option, allowing for a versatile approach to lawn care.

Finally, the HZS18482BVE boasts an impressive 24 HP engine, designed for heavy-duty performance. It is ideal for commercial use or homeowners with large properties. This mower combines efficiency with advanced features, including a high-back seat for maximum comfort and an innovative control panel that provides essential information at a glance.

Across this range, all models are characterized by excellent durability, ergonomic designs, and powerful cutting capabilities. Snapper's commitment to quality is evident in their use of high-grade materials and innovative technologies, allowing users to achieve a perfectly manicured lawn with ease and efficiency. These zero-turn mowers are not just tools; they are essential companions that enhance the mowing experience for both enthusiasts and professionals alike.
Top Page Image Contents