Snapper HZS14331BVE, HZS14381BVE, HZS15421KVE, HZS15422KVE, HZS18482BVE Battery Service

Page 20

Section 4 - ADJUSTMENTS & REPAIR

WARNING

The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid. Wear eye protection. Wash affected areas immediately after having eye or skin contact with electrolyte (acid). Battery acid is corrosive. Rinse empty acid containers with water and mutilate before discarding. If acid is spilled on battery, bench, or clothing, etc., Flush with clear water and neutralize with baking soda. Never attempt to charge battery while installed on the YARD CRUISER. Never use “BOOST” chargers on the battery.

4.4.3. BATTERY SERVICE

1.Remove battery. See Section on Battery Removal

2.Place battery in a well ventilated area on a level surface.

3.Using distilled water, refill cells as required to cover cell plates of which can also be visualized through the plastic battery case.

4.With cell caps removed, connect battery charger to battery terminals. Red to positive (+) terminal and black to negative (-) terminal.

5.Slow charge battery at 1 amp for 10 hours.

6.If battery will not accept charge or is partially charged after 10 hours of charging at 1 amp, replace with new battery, Part Number 6-0753.

4.4.4. BATTERY STORAGE

If YARD CRUISER is to be stored out of season on its rear bumper, it is recommended the battery be removed, charged and stored.

1.Remove battery. (See 4.4.1., Battery Removal)

2.Perform battery service.

3.Bring battery to full charge, if required.

4.Store battery in an area away from the YARD CRUISER on a wood surface. DO NOT STORE BATTERY ON A CONCRETE SURFACE.

4.4.5.NEW BATTERY PREPARATION 1. Remove battery from carton.

2. Place battery in a well ventilated area on a level non-concrete surface.

3. Remove battery cell caps. Fill cells as required with electrolyte (purchased separately) to proper level. Fill to 3/16” above cell plates. Filling battery with electrolyte will bring the battery to 80% charged state.

4. With cell caps removed, connect battery charger to battery terminals; RED to positive (+) and BLACK to negative (-) terminal.

IMPORTANT: 3/16” above cell plates is the recommended level. However do not try to measure this dimension. Never place anything in battery other than specified electrolyte.

WARNING

DO NOT OVERFILL! Never attempt to charge battery while installed on the Yard Cruiser. Never use “BOOST” chargers on the battery.

5.Slow charge the battery at 1 amp for 2 hours to bring the battery to full charge.

6.After charging, check level of electrolyte and add as needed to bring level to 3/16” above cell plates.

7.Reinstall cell caps.

8.Install battery into power unit. Connect over flow tube.

9.Connect positive (+) cable (red) first, from wiring harness to the positive terminal (+) on battery using bolt and nut provided in hardware bag. Connect negative (-) cable (black) last, to negative terminal (-) on battery using bolt and nut. Apply a small amount of grease over terminals to prevent corrosion.

WARNING

Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal which could cause sparks.

4.4.6.BATTERY TESTING

There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current. To perform unloaded testing, check charge condition using either a hydrometer or voltmeter.

1.Using a voltmeter, voltage readings appear instantly to show the state of charge. Remember to hook the positive lead to the battery’s positive terminal, and the negative lead to the negative terminal.

2.A hydrometer measures the specific gravity of each cell. The specific gravity tells the degree of charge; generally, a specific gravity of about 1.265 to 1.280 indicates full charge. A reading of 1.230 to 1.260 indicates the battery should be charged. The chart on the next page shows the charge level as measured by syringe float hydrometer, digital voltmeter and five ball hydrometer.

(Continued on Next Page)

20

Image 20
Contents Yard Cruiser Manual No -6352 REV , 8/23/99Important Safety Instructions Operation Table of Contents Left Console View Right Console ViewIntroduction NomenclatureOperating Instructions PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Manual Start Mower BladeStopping Wheel DriveCutting Height Adjustment Do not park machine on slopesService After First 5 Hours Change Engine OILCheck Mower Blade Single Blade DeckService Every 25 Operating Hours 3.3.1. Engine HZS Model Series 1 Footrest ShownMower Components 5. Mower Blade Spindle Lubrication Important 48 Decks OnlyMower Deck Linkage Lubrication Yard Cruiser Lubrication 1. Front Wheel BearingsStorage OUT of Season Annually END of Each SeasonEngine Air Filter Oil Filter Engine Oil Transaxle Engine Adjustments & Repair Mower Drive Belt AdjustmentBelt Replacement Belt RemovalBlade Brake Mower Deck Adjustment LevelnessFront or Rear View of Deck Triple Blade Deck Adjustments & Repair Front or Rear View of Deck Twin Blade DeckDeck Shown Front to Rear Deck Pitch 33 DeckMower Deck Timing ROD Wheel Brake AdjustmentMower Blade REPAIR/REPLACEMENT 4.3.1. Blade Wear Limits Blade Replacement Battery Battery RemovalBattery Installation 1. Slide battery into battery cradle Blade SharpeningBattery Service Battery StorageNEW Battery Preparation 1. Remove battery from carton Battery TestingProblem Probable Cause Corrective Action Trouble Shooting on NextMAINTENANCE/REPLACEMENT Parts Loss Of TractionUSE HRS Season Service Performed Each100 Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Service Notes REV , 8/23/99 Manual No

HZS14331BVE, HZS14381BVE, HZS15421KVE, HZS15422KVE, HZS18482BVE specifications

Snapper is a recognized name in the outdoor power equipment industry, and its latest series of zero-turn mowers is no exception. The Snapper HZS14331BVE, HZS14381BVE, HZS15421KVE, HZS15422KVE, and HZS18482BVE models bring a host of powerful features, cutting-edge technologies, and user-friendly characteristics to enhance lawn care efficiency.

The HZS14331BVE model is equipped with a reliable 14.5 HP engine, offering a balance of power and fuel efficiency, making it excellent for homeowners with average-sized lawns. Its compact design enhances maneuverability, allowing users to navigate tight spaces with ease. The machine is built with a durable steel frame, ensuring longevity while providing stability on various terrains.

Following closely is the HZS14381BVE, which steps up with an 18 HP engine, providing that extra power for tackling more extensive lawns or tougher grass conditions. This model incorporates a 42-inch cutting deck, allowing for an efficient mowing experience. The deck’s design promotes optimum airflow, resulting in a cleaner cut and better grass dispersal.

The HZS15421KVE offers even more capability with a 21 HP engine. It emphasizes speed and precision, featuring a user-friendly hydrostatic transmission system that allows for easy control and a smooth driving experience. This model is particularly designed for homeowners wanting a machine that combines performance with comfort.

With the HZS15422KVE, users will see a significant upgrade in cutting width, with a robust 54-inch deck that can handle larger properties efficiently. Its comfortable seat and adjustable steering controls ensure that operators can mow for extended periods without fatigue. The model also includes a mulching option, allowing for a versatile approach to lawn care.

Finally, the HZS18482BVE boasts an impressive 24 HP engine, designed for heavy-duty performance. It is ideal for commercial use or homeowners with large properties. This mower combines efficiency with advanced features, including a high-back seat for maximum comfort and an innovative control panel that provides essential information at a glance.

Across this range, all models are characterized by excellent durability, ergonomic designs, and powerful cutting capabilities. Snapper's commitment to quality is evident in their use of high-grade materials and innovative technologies, allowing users to achieve a perfectly manicured lawn with ease and efficiency. These zero-turn mowers are not just tools; they are essential companions that enhance the mowing experience for both enthusiasts and professionals alike.