Snapper HZS14331BVE, HZS14381BVE, HZS15421KVE, HZS15422KVE, HZS18482BVE Engine Manual Start

Page 8

Section 2 - OPERATING INSTRUCTIONS

2.2.2. ENGINE (MANUAL START)

IMPORTANT: When the ignition key is turned to “RUN”, the engine willnot start unless the Parking Brake is engaged and the Blade Switch is in the “Off” position. The operator should be in the seat. Start engine as follows:

1.Move joystick lever to (N) Neutral position. Refer to Figure 2.5.

2.Make certain the blade switch is in the “Off” position. Refer to Figure 2.6.

3.Make certain the parking brake is engaged. Refer to Figure 2.5.

4.Open vent on fuel filler cap by turning counterclockwise. IMPORTANT: Failure to open vent on the fuel filler cap can cause engine to stall. Refer to Figure 2.3.

5.Turn fuel shut off valve to the open position. Refer to Figure 2.3.

6.Move engine speed/choke control to the choke position or pull choke control to choke position. Refer to Figure 2.6.

7.Pull starter rope with a smooth even motion until engine starts. Guide rope back to recoil housing.

8.After engine starts, move engine speed/choke control to the “FAST” position or push choke control in to the “OFF” position, allow a brief warm-up until engine runs smooth.

2.2.3.MOWER BLADE

1.With engine running, move engine speed control to the Rabbit or “fast” position.

2.Pull the blade switch out into the “ON” position to engage the mower blades. See Figure 2.7.

DISENGAGE PARKING

BRAKE

PULL BLADE SWITCH

OUT TO THE “ON”

POSITION

ENGINE SPEED CONTROL IN THE “FAST” POSITION

FIGURE 2.7

3.Release the parking brake. See Figure 2.7.

WARNING

DO NOT operate blades in reverse. STOP BLADES. LOOK and SEE behind and down for children, pets and hazards before and while backing.

4.Move joystick carefully in the desired direction to propel the machine. A small movement of the joystick can cause the machine to move instantly. Move joystick carefully and slowly.

2.3STOPPING

2.3.1.ENGINE

1.Stop engine by turning key to the “OFF” position. See Figure 2.8.

TURN KEY TO “OFF”

OR STOP POSITION

DECAL VIEWED FROM

OPERATOR’S

POSITION

FIGURE 2.8

WARNING

DO NOT leave machine running. STOP engine. STOP blades. Engage parking brake. Remove key. DO NOT park machine on slopes.

2.3.2. WHEEL DRIVE

1.Stop motion of riding mower by moving joystick to neutral (N) position. Refer to Figure 2.8.

2.3.3. MOWER BLADE

1.Push the blade switch in to “OFF” position to disengage or stop the mower blades. Refer to Figure

WARNING

Once blades are disengaged, they should come to a complete stop in 5 seconds. If the blades continue to rotate after 5 seconds, the electric clutch should be checked. Replacement of electric clutch may be necessary. DO NOT continue to operate mower if blades fail to stop in 5 seconds.

2.3.4. PARKING BRAKE

1.Manually position joystick in the neutral position.

2.Engage parking brake by pushing button at the top of lever and then pulling the parking brake lever slowly back to the “ON” position.

3.Release parking brake by pushing button at the top of lever and moving brake lever forward to the “OFF” position. Refer Figure. 2.7.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Yard Cruiser Manual No -6352 REV , 8/23/99Important Safety Instructions Operation Table of Contents Left Console View Right Console ViewIntroduction NomenclatureOperating Instructions PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Manual Start Mower BladeStopping Wheel DriveCutting Height Adjustment Do not park machine on slopesService After First 5 Hours Change Engine OILCheck Mower Blade Single Blade DeckService Every 25 Operating Hours 3.3.1. Engine HZS Model Series 1 Footrest ShownMower Components 5. Mower Blade Spindle Lubrication Important 48 Decks OnlyMower Deck Linkage Lubrication Yard Cruiser Lubrication 1. Front Wheel BearingsStorage OUT of Season Annually END of Each SeasonEngine Air Filter Oil Filter Engine Oil Transaxle Engine Adjustments & Repair Mower Drive Belt AdjustmentBelt Replacement Belt RemovalBlade Brake Mower Deck Adjustment LevelnessFront or Rear View of Deck Triple Blade Deck Adjustments & Repair Front or Rear View of Deck Twin Blade DeckDeck Shown Front to Rear Deck Pitch 33 DeckMower Deck Timing ROD Wheel Brake AdjustmentMower Blade REPAIR/REPLACEMENT 4.3.1. Blade Wear Limits Blade Replacement Battery Battery RemovalBattery Installation 1. Slide battery into battery cradle Blade SharpeningBattery Service Battery StorageNEW Battery Preparation 1. Remove battery from carton Battery TestingProblem Probable Cause Corrective Action Trouble Shooting on NextMAINTENANCE/REPLACEMENT Parts Loss Of TractionUSE HRS Season Service Performed Each100 Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Service Notes REV , 8/23/99 Manual No

HZS14331BVE, HZS14381BVE, HZS15421KVE, HZS15422KVE, HZS18482BVE specifications

Snapper is a recognized name in the outdoor power equipment industry, and its latest series of zero-turn mowers is no exception. The Snapper HZS14331BVE, HZS14381BVE, HZS15421KVE, HZS15422KVE, and HZS18482BVE models bring a host of powerful features, cutting-edge technologies, and user-friendly characteristics to enhance lawn care efficiency.

The HZS14331BVE model is equipped with a reliable 14.5 HP engine, offering a balance of power and fuel efficiency, making it excellent for homeowners with average-sized lawns. Its compact design enhances maneuverability, allowing users to navigate tight spaces with ease. The machine is built with a durable steel frame, ensuring longevity while providing stability on various terrains.

Following closely is the HZS14381BVE, which steps up with an 18 HP engine, providing that extra power for tackling more extensive lawns or tougher grass conditions. This model incorporates a 42-inch cutting deck, allowing for an efficient mowing experience. The deck’s design promotes optimum airflow, resulting in a cleaner cut and better grass dispersal.

The HZS15421KVE offers even more capability with a 21 HP engine. It emphasizes speed and precision, featuring a user-friendly hydrostatic transmission system that allows for easy control and a smooth driving experience. This model is particularly designed for homeowners wanting a machine that combines performance with comfort.

With the HZS15422KVE, users will see a significant upgrade in cutting width, with a robust 54-inch deck that can handle larger properties efficiently. Its comfortable seat and adjustable steering controls ensure that operators can mow for extended periods without fatigue. The model also includes a mulching option, allowing for a versatile approach to lawn care.

Finally, the HZS18482BVE boasts an impressive 24 HP engine, designed for heavy-duty performance. It is ideal for commercial use or homeowners with large properties. This mower combines efficiency with advanced features, including a high-back seat for maximum comfort and an innovative control panel that provides essential information at a glance.

Across this range, all models are characterized by excellent durability, ergonomic designs, and powerful cutting capabilities. Snapper's commitment to quality is evident in their use of high-grade materials and innovative technologies, allowing users to achieve a perfectly manicured lawn with ease and efficiency. These zero-turn mowers are not just tools; they are essential companions that enhance the mowing experience for both enthusiasts and professionals alike.
Top Page Image Contents