Snapper HZS14331BVE, HZS14381BVE, HZS15421KVE, HZS15422KVE, HZS18482BVE Blade Sharpening, Deck

Page 19

Section 4 - ADJUSTMENTS & REPAIR

4.3.2. BLADE SHARPENING

1.Make sure fuel cap is on tight. Turn fuel shut off valve to the “CLOSED” position. Start engine and allow it to run until engine runs out of fuel. Close vent on fuel filler cap. See Figure 2.3.

2.Remove key from ignition switch.

3.Remove spark plug wire(s) and secure away from spark plug(s).

4.Carefully stand YARD CRUISER on rear bumper.

5.Remove blade(s). See Figure 4.14.

6.Inspect condition of blade. Refer to Figure 4.13.

7.If blade is in good condition, sharpen at 22 to 28 degrees. DO NOT sharpen beyond existing cutting edge. See Figure 4.15.

8.Check blade balance after sharpening. If necessary, correct blade balance by grinding the heavy end of blade.

9.Reinstall blade. See Figure 4.14. Torque blade mounting bolts to recommended range of:

33” Deck - 30 to 40 ft. lbs. 38” Deck - 80 to 90 ft. lbs. 42” Deck - 30 to 40 ft. lbs. 48” Deck - 60 to 70 ft. lbs.

33” DECK

38” DECK

42” DECK

48” DECK

FIGURE 4.14

DO NOT SHARPEN

BEYOND ORIGINAL 22º TO 28º

CUTTING EDGE

BLADE TIP

WARNING

Never use a cutting blade that shows signs of excessive wear or damage. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

4.3.3. BLADE REPLACEMENT

1.Remove blade(s). Refer to 4.14. Replace blade(s) if it shows signs of excessive wear or damage.

NOTE: FOR ALL CUTTING BLADE REPLACEMENT PARTS IDENTIFICATION NUMBERS SEE PAGE 22.

WARNING

Before attempting any adjustments or repairs, STOP the engine, remove the key, remove the spark plug wire(s) from the spark plug(s) and secure wire(s) away from plug(s). Never attempt to service or charge the battery while it is installed on the YARD CRUISER. Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal, which could cause sparks. Cables must be connected to battery terminals in the proper position as shown in Figure 4.16.

4.4 BATTERY

4.4.1. BATTERY REMOVAL

1.Tilt seat up to gain access to battery.

2.Observe and note cable positions on battery. See Figure 4.16.

3.Disconnect cables from battery terminals, disconnecting BLACK (Negative) cable first. Disconnect RED (Positive) battery cable. Slide battery from battery cradle.

4.Retain mounting bolts and nuts for future use.

4.4.2.BATTERY INSTALLATION 1. Slide battery into battery cradle.

2. Connect cables to battery terminals. Connect RED (Positive) cable first. Connect BLACK (Negative) cable. See Figure 4.16.

3. Place the positive (+) terminal insulator over positive terminal and cable. See Figure 4.16.

BLACK

NEGATIVE (-)

CABLE

RED

POSITIVE (+)

CABLE

ORIGINAL CUTTING EDGE

FIGURE 4.15

FIGURE 4.16

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Manual No -6352 REV , 8/23/99 Yard CruiserImportant Safety Instructions Operation Table of Contents Nomenclature Left Console ViewRight Console View IntroductionPRE-START Check List Operating InstructionsOn Next Starting & Operation Engine Electric StartWheel Drive Engine Manual StartMower Blade StoppingDo not park machine on slopes Cutting Height AdjustmentSingle Blade Deck Service After First 5 HoursChange Engine OIL Check Mower BladeHZS Model Series 1 Footrest Shown Service Every 25 Operating Hours 3.3.1. EngineYard Cruiser Lubrication 1. Front Wheel Bearings Mower Components 5. Mower Blade Spindle LubricationImportant 48 Decks Only Mower Deck Linkage LubricationEngine Air Filter Oil Filter Engine Oil Transaxle Annually END of Each SeasonStorage OUT of Season Belt Removal Engine Adjustments & RepairMower Drive Belt Adjustment Belt ReplacementFront or Rear View of Deck Triple Blade Deck Mower Deck Adjustment LevelnessBlade Brake Adjustments & Repair Front to Rear Deck Pitch 33 Deck Front or Rear View of DeckTwin Blade Deck Deck ShownMower Blade REPAIR/REPLACEMENT 4.3.1. Blade Wear Limits Wheel Brake AdjustmentMower Deck Timing ROD Blade Sharpening Blade ReplacementBattery Battery Removal Battery Installation 1. Slide battery into battery cradleBattery Testing Battery ServiceBattery Storage NEW Battery Preparation 1. Remove battery from cartonTrouble Shooting on Next Problem Probable Cause Corrective ActionLoss Of Traction MAINTENANCE/REPLACEMENT Parts100 Service Performed EachUSE HRS Season Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Service Notes REV , 8/23/99 Manual No

HZS14331BVE, HZS14381BVE, HZS15421KVE, HZS15422KVE, HZS18482BVE specifications

Snapper is a recognized name in the outdoor power equipment industry, and its latest series of zero-turn mowers is no exception. The Snapper HZS14331BVE, HZS14381BVE, HZS15421KVE, HZS15422KVE, and HZS18482BVE models bring a host of powerful features, cutting-edge technologies, and user-friendly characteristics to enhance lawn care efficiency.

The HZS14331BVE model is equipped with a reliable 14.5 HP engine, offering a balance of power and fuel efficiency, making it excellent for homeowners with average-sized lawns. Its compact design enhances maneuverability, allowing users to navigate tight spaces with ease. The machine is built with a durable steel frame, ensuring longevity while providing stability on various terrains.

Following closely is the HZS14381BVE, which steps up with an 18 HP engine, providing that extra power for tackling more extensive lawns or tougher grass conditions. This model incorporates a 42-inch cutting deck, allowing for an efficient mowing experience. The deck’s design promotes optimum airflow, resulting in a cleaner cut and better grass dispersal.

The HZS15421KVE offers even more capability with a 21 HP engine. It emphasizes speed and precision, featuring a user-friendly hydrostatic transmission system that allows for easy control and a smooth driving experience. This model is particularly designed for homeowners wanting a machine that combines performance with comfort.

With the HZS15422KVE, users will see a significant upgrade in cutting width, with a robust 54-inch deck that can handle larger properties efficiently. Its comfortable seat and adjustable steering controls ensure that operators can mow for extended periods without fatigue. The model also includes a mulching option, allowing for a versatile approach to lawn care.

Finally, the HZS18482BVE boasts an impressive 24 HP engine, designed for heavy-duty performance. It is ideal for commercial use or homeowners with large properties. This mower combines efficiency with advanced features, including a high-back seat for maximum comfort and an innovative control panel that provides essential information at a glance.

Across this range, all models are characterized by excellent durability, ergonomic designs, and powerful cutting capabilities. Snapper's commitment to quality is evident in their use of high-grade materials and innovative technologies, allowing users to achieve a perfectly manicured lawn with ease and efficiency. These zero-turn mowers are not just tools; they are essential companions that enhance the mowing experience for both enthusiasts and professionals alike.
Top Page Image Contents