Snapper EMLP21501KWV, EMLP21601, EMLP21601E Cutting Height Adjustment, Recycling Operation

Page 8

Section 2 - OPERATING INSTRUCTIONS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Remove key. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

2.5CUTTING HEIGHT ADJUSTMENT

1. Pull the cutting height adjusting handle outward and move to desired cutting height. See Figure 2.7.

IMPORTANT: DO NOT flex the cutting height adjusting handle outward beyond what is required to change cutting height. Pulling outward too far may cause damage to the handle.

CUTTING HEIGHT

ADJUSTING HANDLE

FIGURE 2.7

2.6 RECYCLING OPERATION

Converting this mower to the recycling operation requires no tools. First, STOP engine. Raise discharge door located at rear of machine. Remove grass catcher. Insert recycling plug fully into discharge opening. Allow discharge door to close. See Figure 2.8.

NOTE: For best recycling results, cut up to a maximum of 1/3 of grass blade length and recycle ONLY when grass is dry.

1.Set the cutting height at the highest cutting position.

2.Move engine speed control to “FAST” (Rabbit) position.

3.Move ground speed control to slowest speed setting.

4.Proceed mowing slowly. If grass is very dense, raise cutting height to improve recycling performance.

LIFT DISCHARGE

DOOR

INSERT

RECYCLING

PLUG

FIGURE 2.8

2.7INSTALLATION of GRASS CATCHER

1.Follow WARNING statement found on this page.

2.Lift discharge door located at the rear of machine. See Figure 2.9.

3.Install grass catcher onto the rear of machine. Position the rod ends of catcher frame over the tabs located at the rear of deck. Release discharge door, which is spring loaded, onto top of grass catcher.

LIFT DISCHARGE

DOOR

FIT ROD

ENDSTABS OVER TABS

CATCHER

HANDLE

GRASS

CATCHER

FIGURE 2.9

WARNING

DO NOT operate mower without entire grass catcher, side chute or recycling plug in place. Grass Catcher components are subject to deterioration during normal use. Inspect frequently and replace worn or damaged components immediately.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents European 21 Cast Aluminum Deck M Model Walk Mowers Series Preparation Protection for ChildrenSlope Operation Maintenance and Storage OperationTable of Contents Nomenclature FamiliarizationIntroduction Operating Instructions PRE-START Check ListStarting & Operation 2.2.1. Engine & Blade Primer Models Recoil StartHandle Height Adjustment Engine & BladeChoke Models Recoil Start Propelling MowerRecycling Operation Cutting Height AdjustmentInstallation of Grass Catcher Maintenance Service After First 5 Hours 3.2.1. Change Engine OILGrease Level in Transmission Wheel Drive ControlService Annually Storage ProcedureCheck Mower Blade Check Engine to Transmission Drive BeltRepair & Adjustments Mower Blade Replacement 4.1.1. Standard Blade Wear LimitBlade Sharpening On NextWheel Drive Control Adjustment Belt Service Adjustments & Repair Battery Battery RemovalBattery Installation Battery ServiceState of Charge Digital Voltmeter Battery TestingNEW Battery Preparation Problem Probable Cause Corrective Action Using Recoil StarterStart Using Engine Will NotService Performed Each Clean Sponge Element Engine Manual100 USE HRS SeasonDecal Identification Height Control Decal Year Limited Warranty Disclaimer of WarrantyEuropean Cast Aluminum Deck M Model Walk Mowers Series

EMLP21501KWV, EMLP21601, EMLP21601E specifications

Snapper EMLP21501KWV, EMLP21601, and EMLP21601E are innovative lawn care solutions designed to meet the diverse needs of homeowners and professional landscapers alike. These models stand out in the lawn maintenance industry due to their unique features, advanced technologies, and reliable performance.

The Snapper EMLP21501KWV is notable for its powerful engine and user-friendly design. It is equipped with a robust 150cc engine that ensures efficient mowing performance across various terrain types. This model features a 21-inch steel mowing deck, which enables a precise cutting width, ensuring an even finish on lawns of all shapes and sizes. One of the main characteristics of the EMLP21501KWV is its ease of use, thanks to the push-button start system, which allows users to start the mower effortlessly.

In contrast, the EMLP21601 and EMLP21601E models introduce advanced features that take lawn care to the next level. The EMLP21601 is equipped with a more powerful engine, capable of delivering enhanced torque and performance. This model also features Snapper's signature Smart Speed technology, which allows users to choose from different speed settings for efficient mowing in various conditions. The larger 21-inch deck is complemented by an adjustable cutting height, providing versatility for different grass types and seasonal conditions.

The EMLP21601E further enhances the user experience with electric start capabilities, making it easier for homeowners to start the mower without the hassle of pull cords. Additionally, this model includes a rear bagger option for convenient grass collection, which helps maintain a tidy lawn and reduces cleanup time after mowing.

All three models are designed with durability in mind, featuring high-quality components that can withstand the rigors of regular use. They are equipped with ergonomic handles, ensuring a comfortable grip during operation, and foldable designs for easy storage in smaller spaces.

In summary, the Snapper EMLP21501KWV, EMLP21601, and EMLP21601E mowers offer powerful performance, advanced technology, and user-friendly features that cater to a wide range of mowing needs. Whether for personal use or professional landscaping, these models provide an excellent combination of power, efficiency, and convenience, making them an ideal choice for anyone looking to maintain a beautiful lawn.
Top Page Image Contents