Snapper CP214012R2 Recycling Operation Optional Accessory, Installation of Grass Catcher

Page 8

Section 2 - OPERATING INSTRUCTIONS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

2.6RECYCLING OPERATION - OPTIONAL ACCESSORY

Recycling operation requires optional accessory.

NOTE: For best recycling results, cut up to a maximum of 1/3 of grass blade length and recycle ONLY when grass is dry.

1.Set all wheels in the highest cutting position (Notch 6).

2.Move engine speed control to “FAST” (Rabbit) position.

3.Move ground speed control to slowest speed setting.

4.Proceed mowing slowly. If grass is very dense, lower each rear wheel latch one notch lower than the front wheel latches to improve recycling performance.

2.7INSTALLATION of GRASS CATCHER

Position grass bag between handles. See Figure

2.8.Install grass catcher by sliding connector over flange of adapter. Attach grass bag hooks over middle handle cross bar. See Figure 2.9.

LOWER HANDLES

HANDLE

BAG CONNECTOR

ADAPTER

FLANGE

HOOK BAG

HANDLE OVER

LOWER HANDLES

SLIDE CONNECTOR

OVER END OF

ADAPTER FLANGE

FIGURE 2.9

WARNING

DO NOT operate without entire Grass Catcher or guard in place. Grass Catcher components are subject to deterioration during normal use. Inspect frequently and replace worn or damaged components immediately.

2.8REMOVING and DUMPING GRASS CATCHER

1.Grasp bag connector and bag handle as shown. See Figure 2.8.

2.First, lift up on bag handle, removing it from the mower handle. Then lift up on bag connector removing it from the adapter flange.

3.Dump bag by pulling bag slider off of Z-Fold at rear of bag, opening bag.

4.To close bag, fold rear of bag into Z-shape, keeping edges aligned. Note: an illustration of folding the Z-shape is attached to the bag.

5.Grasp the edge of the Z-fold, and while holding the slider, pull the Z-fold fully into the slider. See Figure 2.10.

GRASP SLIDER. PULL

Z-FOLD INTO SLIDER

PULL

FIGURE 2.8

FIGURE 2.10

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Steel Deck Walk Mowers Commercial Model Series Important Safety Instructions Operation Table of Contents Introduction NomenclatureOperating Instructions PRE-START Check ListStopping Cutting Height AdjustmentHandle Height Adjustment Recycling Operation Optional Accessory Installation of Grass CatcherMaintenance Service After First 5 HoursCheck Engine Drive Belt Check Grease Level in TransmissionCheck Mower Blade Engine Air Filter Engine Oil Service AnnuallyStorage Procedure Mower Blade Replacement 4.1.1. Standard Blade Wear Limit Blade SharpeningOn next Wheel Drive Control AdjustmentDriven Disc Service Drive Spring Repair/Replacement Driven Disc AdjustmentReplacing Driven Disc Rubber Ring Replacing Bearing In Driven Disc Belt Service Engine Drive Belt Replacement 1. Empty the fuel tankPulley Position Troubleshooting Problem Probable Cause Corrective ActionUSE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Steel Deck Walk Mowers Commercial Model Series

P215013KWV, CP214012R2, CP215512KWV, CP216512RV, CP216012RV specifications

The Snapper CP215512KWV, CP216012RV, CP214012R2, CP216512RV, and P215013KWV represent a series of innovative and efficient lawn mowers designed to cater to the varying needs of homeowners and landscapers alike. These models are known for their superior performance, durability, and user-friendly features, making them popular choices in the outdoor equipment market.

One of the standout features across these models is their powerful engines, designed to deliver reliable performance for cutting grass in various conditions. The CP215512KWV, for instance, is equipped with a robust engine that ensures efficient operation, while the CP216012RV boasts enhanced power for tackling thicker grass and tougher terrain. These mowers feature variable speed control, allowing users to adjust the cutting speed to match their comfort level and the specific type of lawn they are maintaining.

Additionally, the Snapper mowers come with advanced cutting technology. The signature 3-in-1 cutting system enables users to mulch, bag, or side discharge clippings, providing flexibility depending on lawn care preferences. This versatility is complemented by adjustable cutting heights, allowing users to choose the optimal grass length for their lawns.

Durability is a key characteristic of these models. Built with high-quality materials and reinforced decks, they can withstand the rigors of regular use. The CP214012R2, for example, features a heavy-duty steel deck that not only enhances stability during operation but also provides a longer lifespan for the mower.

Convenience features such as self-propulsion systems and easy-start engines further enhance the user experience. The CP216512RV model incorporates ergonomic handles and lightweight designs, making it easier to maneuver across lawns of various sizes. Additionally, the foldable handles simplify storage and transport.

With a focus on modern technology, Snapper has integrated cutting-edge technology into these mowers to improve efficiency and reduce maintenance requirements. Features such as easy-access air filters and maintenance reminders make it simpler for users to keep their machines in optimal condition.

In summary, the Snapper CP215512KWV, CP216012RV, CP214012R2, CP216512RV, and P215013KWV offer a blend of power, versatility, and durability that makes them suitable for both residential and commercial use. Their thoughtful design and reliable technology contribute to a superior mowing experience, ensuring that users achieve an immaculate lawn with less effort.
Top Page Image Contents