Snapper 5900686 manual Service and Maintenance, Safe Handling of Gasoline, Maintenance and Storage

Page 10

Safety

Operator Safety

SERVICE AND MAINTENANCE

To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

Safe Handling of Gasoline

1.Extinguish all cigarettes, cigars, pipes, and other sources of ignition.

2.Use only approved gasoline containers.

3.Never remove the gas cap or add fuel with the engine running. Allow the engine to cool before refueling.

4.Never fuel the machine indoors.

5.Never store the machine or fuel container where there is an open flame, spark, or pilot light such as near a water heater or other appliance.

6.Never fill containers inside a vehicle or on a truck bed with a plastic bed liner. Always place containers on the ground away from your vehicle before filling.

7.Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

8.Keep nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

9.If fuel is spilled on clothing, change clothing immediately.

10.Never over-fill the fuel tank. Replace gas cap and tighten securely.

11.Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive.

12.If fuel is spilled, do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until fuel vapors have dissipated.

13.Replace all fuel tank caps and fuel container caps securely.

Maintenance and Storage

1.Always observe safe refueling and fuel handling practices when refueling the unit after transportation or storage.

2.Always follow the engine manual instructions for storage preparations before storing the unit for both short and long term periods.

3.Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.

4.Never store the machine or fuel container inside where there is an open flame, such as in a water heater. Allow unit to cool before storing.

5.Shut off fuel while storing or transporting. Do not store fuel near flames or drain indoors.

6.Keep all hardware, especially blade attachment bolts, tight and keep all parts in good working condition. Replace all worn or damaged decals.

7.Never tamper with safety devices. Check their proper operation regularly.

8.Disengage drives, lower implement, set parking brake, stop engine and remove key or disconnect spark plug wire. Wait for all movement to stop before adjusting, cleaning or repairing.

9.Clean grass and debris from cutting units, drives, mufflers, and engine to prevent fires. Clean up oil or fuel spillage.

10.Let engine cool before storing and do not store near flame.

11.Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting.

12.Park machine on level ground. Never allow untrained personnel to service machine.

13.Use jack stands to support components when required.

14.Carefully release pressure from components with stored energy.

15.Disconnect battery or remove spark plug wire before making any repairs. Disconnect the negative terminal first and the positive last. Reconnect positive first and negative last.

16.Use care when checking blades. Wrap the blade(s) or wear gloves, and use caution when servicing them. Only replace blades. Never straighten or weld them.

17.Keep hands and feet away from moving parts. If possible, do not make adjustments with the engine running.

18.Charge batteries in an open well ventilated area, away from spark and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothes and use insulated tools.

19.Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer’s recommended parts, when necessary.

20.Check brake operation frequently. Adjust and service as required.

21.Use only factory authorized replacement parts when making repairs.

22.Always comply with factory specifications on all settings and adjustments.

23.Only authorized service locations should be utilized for major service and repair requirements.

24.Never attempt to make major repairs on this unit unless you have been properly trained. Improper service procedures can result in hazardous operation, equipment damage and voiding of manufacturer’s warranty.

25.Units with hydraulic pumps, hoses, or motors: WARNING: Hydraulic fluid escaping under pressure may have sufficient force to penetrate skin and cause serious injury. If foreign fluid is injected into the skin it must be surgically removed within a few hours by a doctor familiar with this form of injury or gangrene may result. Keep body and hands away from pin holes or nozzles that eject hydraulic fluid under high pressure. Use paper or cardboard, and not hands, to search for leaks. Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before applying pressure to the system. If leaks occur, have the unit serviced immediately by your authorized dealer.

26.WARNING: Stored energy device. Improper release of springs can result in serious personal injury. Springs should be removed by an authorized technician.

8

www.SnapperPro.com

Image 10
Contents Description Briggs & Stratton Yard Power Products GroupModel Number Date Purchased Table of Contents Operating Safety Operator SafetySafety Rules and Information Read the ManualThrown Objects Slope OperationMoving Parts Retaining WALLS, DROP-OFFS, and Water Roll BAR USEOverhead Obstacles Fuel and Maintenance Enclosed AreasPreparation TrainingOperation Ignition System Gasoline Models Towed Equipment RIDE-ON UnitsEmissions Periods of exposureMaintenance and Storage Service and MaintenanceSafe Handling of Gasoline Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals This unit has been designed and manufactured to provideSafety Icons Safety Interlock SystemOperational Safety Checks North American Safety IconsFeatures and Controls Identification NumbersIgnition Switch Features and ControlsSeat Adjustment Lever Control FunctionsFeatures & Controls Operation General Operating SafetyChecks Before Starting Seat Adjustment Check Tire PressuresFoot Pedal Adjustment Mowing Height AdjustmentTo adjust pedal position Keep roll bar in the raised position and use the seat belt Lower the roll bar only when necessary and Never remove itRaise and Lower the Roll Bar To Lower the Roll BarStopping the Rider Starting the EnginePushing the Rider By Hand Forward Travel Practice Zero Turn Driving PracticeForward Reverse Travel Executing an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Executing TurnsHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Methods Mulching Requires Excellent Mowing Conditions Attaching a TrailerProper Mulching Engine Speed & Ground Speed for MulchingSafety Items Before Every Spring Regular MaintenanceMaintenance Schedule Hours Fall Check Rider / Mower for loose hardwareFuel Filter Engine MaintenanceChecking / Adding Fuel Change Oil & FilterOil LubricationGrease Lubricating the Front CastersChange Hydraulic Oil Filter Check Hydraulic Oil LevelChange Interval Every 250 Hours Filter Part Number Inspecting the Mower Blades Servicing The Mower BladesNever weld or straighten bent mower blades Reinstalling the Mower Blades Balancing the Mower Blade NailGround Speed Control Lever Adjustment Speed Balancing AdjustmentNeutral Adjustment Parking Brake AdjustmentReturn-to-Neutral Adjustment Deck Rod Timing Adjustment Deck Leveling AdjustmentMower Belt Replacement To avoid damaging belts, do not PRY Belts Over PulleysHydraulic Pump Drive Belt Replacement Use extreme caution when removing this springBattery Maintenance Charging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryThis HOOK-UP for Negative Ground Vehicles Starter Switch Jumper Cable StartingVehicle Battery Jumper Cable To Ground Engine Block Make Certain Vehicles do not TouchTemporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysTroubleshooting the Rider Troubleshooting ChartProblem Cause Remedy Troubleshooting Troubleshooting Troubleshooting Common Cutting ProblemsEngine SpecificationsDimensions ChassisFerris Limited Warranty Tractor Mower Deck