|
|
|
|
|
| Troubleshooting | |
| Rider Troubleshooting Continued. |
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Problem | Cause | Remedy | ||||
| Engine runs, but rider will | 1. | Hydraulic release valve(s) | 1. | Turn valve(s) clockwise to close. |
| |
| not drive. |
| in “open” position. |
|
|
|
|
|
| 2. | Belt is broken. | 2. | See Drive Belt Replacement. | ||
|
| 3. | Drive belt slips. | 3. | See problem and cause below. | ||
|
| 4. | Brake is not fully released. | 4. | See authorized service dealer | ||
|
|
|
|
|
|
| |
| Rider drive belt slips. | 1. | Pulleys or belt greasy or oily. | 1. | Clean as required. | ||
|
| 2. | Tension too loose. | 2. | Adjust spring tension. | ||
|
|
|
|
| See Drive Belt Replacement | ||
|
| 3. | Belt stretched or worn. | 3. | Replace belt. | ||
|
|
|
|
|
|
| |
| Brake will not hold. | 1. | Brake is incorrectly adjusted. | 1. | See Brake Adjustment. | ||
|
| 2. | Brake pads worn. | 2. | Replace with new brake pads. | ||
|
|
|
|
|
|
| |
| Rider steers or handles poorly. | 1. | Steering linkage is loose. | 1. | Check and tighten any loose connections. | ||
|
| 2. | Improper tire inflation. | 2. | See Regular Maintenance Section. | ||
|
|
|
|
|
|
|
|
| Troubleshooting the Mower |
|
|
|
|
|
|
| Problem | Cause | Remedy |
| |||
| Mower will not raise. | 1. | Lift linkage not properly attached | 1. | See authorized service dealer for repair. | ||
|
|
| or damaged. |
|
|
|
|
|
|
|
|
|
|
| |
| Engine stalls easily with | 1. | Engine speed too slow. | 1. | Set to full throttle. | ||
| mower engaged. | 2. | Ground speed too fast. | 2. | Decrease Ground Speed. | ||
|
| 3. | Cutting height set too low. | 3. | Cut tall grass at maximum cutting | ||
|
|
|
|
| height during first pass. | ||
|
| 4. | Discharge chute jamming | 4. | Cut grass with discharge pointing toward | ||
|
|
| with cut grass. |
| previously cut area. | ||
|
|
|
|
|
|
| |
| Excessive mower vibration. | 1. | Blade mounting bolts are loose. | 1. | Tighten to 70 ft.lbs. (94 N.m.). | ||
|
| 2. | Mower blades, arbors, | 2. | Check and replace as necessary. | ||
|
|
| or pulleys are bent. |
|
|
|
|
|
| 3. | Mower blades are out | 3. | Remove, sharpen, and balance blades. | ||
|
|
| of balance. |
| See Maintenance Section. | ||
|
| 4. | Belt installed incorrectly. | 4. | Reinstall Correctly. | ||
|
|
|
|
|
|
| |
| Excessive belt wear or breakage. | 1. | Bent or rough pulleys. | 1. | Repair or replace. | ||
|
| 2. | Using incorrect belt. | 2. | Replace with correct belt. | ||
|
|
|
|
|
|
| |
| Mower drive belt slips | 1. | Idler pulley spring broken or not | 1. | Repair or replace as needed. | ||
| or fails to drive. |
| properly attached. |
|
|
|
|
|
| 2. | Mower drive belt broken. | 2. | Replace drive belt. | ||
|
|
|
|
|
|
| |
| Mower does not engage. | 1. | Electrical wiring damage. | 1. | Locate & repair damaged wire. | ||
|
| 2. | PTO clutch not adjusted | 2. | See PTO Clutch Adjustment section | ||
|
| 3. | Battery voltage too low. | 3. | Recharge battery and check alternator. | ||
|
|
|
|
| See Battery Maintenance section. |
Maintenance
43