Snapper 331522KVE, 3314522BVE Starting & Operation, Engine Electric Start, Engine Manual Start

Page 8

Section 2 - OPERATING INSTRUCTIONS

2.3STARTING & OPERATION

2.3.1. ENGINE (ELECTRIC START) (Continued)

8.Should the battery be too weak to start the engine, refer to Section “ENGINE (MANUAL START)” to manually start the electric start engines.

9.On Model 3314522BVE, the engine is equipped with a fuel shut-off solenoid. If the battery is dead, the engine can be started with the recoil back-up starter if the throttle control is in the choke position (HOT engine or COLD engine).

2.3.2. ENGINE (MANUAL START)

IMPORTANT: When the ignition key is turned to “ON”, and the recoil handle is pulled, the engine will turn over, but will not start unless the Clutch/Brake Pedal is pressed all the way down with Parking Brake engaged (See Figure 2.8) and the Blade Lever is in the “Off” position (See Figure 2.4). Start engine as follows:

1.Move transmission shift lever to (N) Neutral position. DO NOT start engine with transmission shift lever in a drive position.

WARNING

It is possible to start engine with transmission shift lever in a drive position. Follow starting instructions carefully.

2.Make certain the Blade Lever is in the “OFF” position. See Figure 2.4.

3.Press Clutch/Brake Pedal all the way down, move Parking Brake Latch over and release the Clutch/Brake Pedal to set Parking Brake. See Figure 2.8.

TO START ENGINE,

PUSH CLUTCH/BRAKE

PEDAL ALL THE DOWN

4.Open vent on fuel filler cap by turning counterclockwise. NOTE: Failure to open vent on the fuel filler cap can cause engine to stall.

5.Move engine speed control to the choke position to start a cold engine. See Figure 2.6.

6.Turn key to “ON” position. See Figure 2.9.

KEY

FIGURE 2.9

7.Pull starter rope with a smooth, even motion until engine starts. Always guide the starter rope back into the recoil housing. Never allow rope to snap back. After Engine starts, move engine speed control to the “FAST” position.

8.Allow a brief warm-up until engine runs smooth.

MOVE

PARKING

BRAKE

LATCH

OVER

FIGURE 2.8

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Rear Engine Riding Mower Series Manual No -4390 Rev 1, 8/27/01Important Safety Instructions Operation Table of Contents Introduction NomenclatureOPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Manual Start Starting & OperationEngine Electric Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeDo not park the machine on slopes Cutting Height AdjustmentStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideChange Engine OIL Service After First 5 HoursService Engine AIR Cleaner Check Mower Blade Blade Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltService Brake / Park Brake Service Every 25 Operating Hours Battery Fluid LevelClean Mower Deck Interlock SystemFront Wheel Bearing Lubrication Rear Axle Bearing LubricationService Annually EngineFuel Filter Every TWO YearsRemoving Fuel Tank Engine Adjustments & Repair Blade Brake AdjustmentFront to Rear Levelness 30 Decks Mower Deck AdjustmentFront to Rear Levelness 28, & 33 Decks Mower Drive Belt Adjustment for 28 & 30 Decks only Service BRAKE/PARK Brake Adjustment Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningMower Drive Belt Replacement Belt ReplacementBelt Removal 28 & 30 DecksBattery Battery Removal Battery InstallationBattery Service Battery StorageNEW Battery Preparation 1. Remove battery from carton Battery TestingSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopLoss Of Traction Blades Not CuttingCutting Grass ImproperlySubject Service Reference To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Rear Engine Riding Mower Series

301222BE, 281222BE, 3314522BVE, 331522KVE specifications

Snapper 301222BE, 3314522BVE, 281222BE, and 331522KVE are advanced lawn care equipment offerings that cater to both residential and commercial users, emphasizing efficiency, durability, and innovative technology. Each model showcases unique features designed to optimize performance and enhance user experience.

The Snapper 301222BE model is known for its robust build, equipped with a powerful Briggs & Stratton engine that ensures reliable starting and sustained performance. Its Easy Start technology simplifies the ignition process, making it user-friendly even for novice operators. The 21-inch steel cutting deck provides a balanced mowing experience, ensuring even grass cutting with minimal effort. This model also features a dual (Rear and Side) discharge function, giving users flexibility in managing grass clippings.

Similarly, the Snapper 3314522BVE combines a powerful engine with a reinforced steel deck, ensuring durability and longevity. What sets it apart is its cutting-edge Smart Mulching technology, which finely chops grass clippings and redistributes them back into the lawn as natural fertilizer. This not only enhances lawn health but also reduces the need for additional lawn care products. The 3314522BVE also incorporates a user-friendly height adjustment lever, allowing operators to easily switch between cutting heights.

The Snapper 281222BE is designed with an emphasis on compactness without sacrificing power. It features a 19-inch cutting deck and a lightweight design, making it perfect for maneuvering around smaller lawns and tight spaces. The 281222BE also boasts an ergonomic handle for increased comfort during prolonged use, making it a perfect choice for homeowners seeking a practical and effective mowing solution.

On the other hand, the 331522KVE stands out with its innovative technology featuring a variable speed self-propulsion system, allowing users greater control over their mowing speed. This model also includes an integrated grass catcher which efficiently collects clippings, reducing cleanup time after mowing. The high-wheel design on this model enhances stability on uneven terrain, making it suitable for a wide range of lawn conditions.

In summary, Snapper’s range of models, including the 301222BE, 3314522BVE, 281222BE, and 331522KVE, exemplifies a blend of innovative engineering and practical design. With features tailored to meet diverse lawn care needs, these models represent a step forward in enhancing efficiency and ease of use in lawn maintenance. Whether for residential lawns or commercial landscapes, Snapper mowers are designed to deliver exceptional results while ensuring user comfort and satisfaction.
Top Page Image Contents