Snapper 1726794 manual Install Idler Assembly & Belt Cover, Install Turbo Drive Pulley

Page 8

Initial Turbo Installation

E

B

D

 

A

 

 

 

C

Figure 9. Install Idler Assembly

 

A. Idler Assembly.

D. Locknuts, 5/16-18

B. Belt Guide

E. Taptite Screws

C. Capscrew, 5/16-18 x 7/8

 

Install Idler Assembly & Belt Cover

Torque to

E

55-70 ft. lbs.

D

Original

F

Pulley and

C

Spacer

 

B

 

A

Figure 10. Install Turbo Drive Pulley

A. Original Pulley & Spacer

D. Spring Washer

B. Spacer, W/Notches (New)

E. Sleeve Nut

C. Pulley (New)

F. Spacer (New)

1.See Figure 9. Remove and discard the two taptite screws from locations (E).

2.Insert two 5/16-18 x 7/8 capscrews (C) through the mower deck and arbor. Tighten the capscrews.

3.Mount the idler pulley assembly (A) to the deck using the two 5/16-18x 7/8 capscrews (C) and 5/16-18 whi- zlock nuts (D).

Install Turbo Drive Pulley

1.See Figure 10. Remove the arbor drive belt from the right side arbor pulley.

2.Remove and discard the flange nut and spring wash- ers securing the arbor pulley and spacer (A). Retain the pulley and spacer (A).

3.Install the new spacers (B & F), turbo drive pulley (C), spring washer (D), and sleeve nut (E). Be sure the notches in the pulleys and spacers are aligned. Install the spring washer concave side down. Torque the sleeve nut to 55-70 ft. lbs. (74-95 N.m).

4.Reinstall the arbor drive belt on the lower pulley.

C

D

G

B

 

F

H

 

E

A

 

 

 

Figure 11. Anchor Bracket Assembly

A. Anchor Bracket

 

E. Nut, Hex, 5/16

B. Lockwasher, 5/16, Large F. Wing Nut, 5/16

C. Latch, Spring

 

G. Locknut, 5/16

D. Lockwasher, 5/16, Small H. Capscrew, 5/16-18 x 2-1/2

Install Anchor Bracket

1.See Figure 12. If not already done, assemble the anchor bracket and related components as shown in Figure 11.

2.Attach the anchor bracket assembly (B, Figure 12) to the mower deck using 5/16-18 x 1 capscrews (A) and 5/16-18 locknuts (C).

NOTE: The deflector latch MUST secure the deflector in a down position—as shown in Figure 7.

B

C

 

A

Figure 12. Anchor Bracket Installation

A. Capscrews, 5/16-18 x 1 B. Anchor Bracket C. Locknut, 5/16-18

7

Image 8
Contents Clean Sweep Triple Catcher OPERATOR’S ManualTable of Contents Safety Rules Information General Operating Instructions Installation Deflector Removal Install Discharge BaffleInstall Deflector Hinge Assembly Install Deflector ModelsInstall Anchor Bracket Install Idler Assembly & Belt CoverInstall Turbo Drive Pulley Install Mounting Bracket Install Belt Cover PlateInstall Turbo Belt Secure Belt Cover Install Turbo BlowerInstall Turbo Drive Belt Initial Counter Balance & Weight Carrier Installation Front Weight Carrier InstallationInitiai Hitch & Tube Installation Initial Hitch & Tube Installation Assemble Tubes & DeflectorInstall Cover Assemble Catcher BagsRemoving & Re-attaching Grass Catcher Removing and Re-attaching Grass Catcher Re-attaching the Grass CatcherFront Weight Carrier Group Clean Sweep Triple Catcher Series Triple Catcher Group Consumer Z Triple Bagger 986509 Tube & Hitch Group Consumer Z Triple Bagger 986506 Turbo Mounting Group 986508 Turbo Mounting Group Bracket Z Hardware Identification & Torque Specifications