Snapper P2167517BVE, WP216517B important safety instructions Pulley Position, Deckbracket

Page 20

Section 4 - REPAIR & ADJUSTMENTS

WARNING

PULLEY POSITION

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.4.1.Engine Drive Belt Replacement

(Stretch Type Belts)

(Continued From Previous Page)

IMPORTANT: Drain fuel tank before tipping mower.

SLOT IN END

OF DRIVE DISC

BOLT

DECKBRACKET

(PARTIALLY SHOWN) k.,J'_

BOLT RETAINER

DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the

engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be

replaced.

3.Remove the driven disc. Refer to Section

"Replacing Driven Disc Rubber Ring" for driven disc removal procedure.

4.Drain fuel tank before tipping mower. Do not tilt mower with spark plug or carburetor down. Tilt mower up on its rear wheels and remove blade and blade hub. Assistance from another person may be necessary to hold mower in the tilted position.

5.Hold the slotted end of the drive disc bolt with a screwdriver and remove the nut and internal tooth

lock washer. See Figure 4.16.

6.Remove the belt cover located under deck.

7.Lift the drive disc up and remove worn belt.

8.Loop one end of new belt over engine pulley and insert the other end through slot in deck. Refer to Figure 4.15.

9.Loop the belt around the pulley on the bottom of the drive disc.

10.Reinstall drive disc and retaining hardware.

"_ _'_ INTERNAL TOOTH

(_ ) e,----'--" LOCKWASHER

NUT

FIGURE 4.16

4.4.2.Transmission Poly-V Belt Replacement

1.Remove the driven disc. Refer to Section on "Replacing Driven Disc Rubber Ring" for procedure.

2.Note the routing of the old belt around the three pulleys before removing it. See Figure 4.17.

3.Place new Poly-V Belt over end of hex shaft and onto drive pulley.

4.Work belt onto top of idler pulley.

5.Twist belt sideways and pull it upward between the differential bracket and driven pulley and then down into the pulley groove. Make sure the Poly-V Belt is above belt guide. See Figure 4.17.

IDLER

BRACKET

DRIVE

PULLEY

IMPORTANT: 1) The square shoulder of the drive disc bolt must fit into the square hole of the bushing.

2)The square end of bushing must fit into the bracket slot.

11.Reinstall belt cover and tighten bolts securely.

12.Reinstall blade hub and cutter blade.

Recommended torque for blade cap screw is 40 ft. Ibs.

HEX SHAFT -

BELT GUIDE

PULLEY

f

ROUTING OF POLY-V BELT

FIGURE 4.17

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Steel Deck Walk Mowers Series Model Number ExplanationImportant Safety Instructions Georgia 30253. PhoneOperation Contents Briggshonda Engineengine Speedspeed Controlcontrol Introduction NomenclatureRecoil Start Models PRE-START Check ListStarting & Operation Engine & Blade Stopping Starting & Operation 2.2.1. Engine & BladePropelling Mower Handle Height Adjustment Cutting Height AdjustmentInstallation of Grass BAG Adapter Installation of Grass BAG Door Type BagRecycling Operation On NextInstallation of Grass Catcher Slide Closure Type Removing and Dumping Grass CatcherInstall Slide Discharge Deflector Slot Service After First 5 Hours 3.2.1. Change Engine OIL IntroductionImportant Drain fuel tank before tipping machine Dispose of drain oil properlyStorage Procedure Check Mower BladeCheck Engine Drive Belt Check Transmission POLY-V BeltMower Blade Replacement Standard Blade Wear Limit WearlimitBlade Sharpening DJDO Notuseon MowerWheel Drive Control Adjustment Are for self-propelled models onlyDriven and Drive Disc Service Cleaning Drive Disc & Driven DiscDriven Disc Adjustment Important If machine drive system continuesReplacing Rubber Driven Disc Install NEW Driven Disc Belt Service Engine Drive Belt Replacement Stretch Type BeltsPulley Position DeckbracketBattery Service NEW Battery Preparation Battery TestingBattery Service 1. Remove battery Battery StorageTroubleshooting HRS HR8 HR8 Season Service Performed Each USE HRSMAINTENANCE/REPLACEM ENT Parts Year Limited Warranty Disclaimer of WarrantyIllustration of how dirt can How Maintenance can protect it Cost YOU Money Check OIL Level Before Each START-UP Starting Check List Snapper Product Registration Form Page Page Steel Deck Walk Behind Mowers Series

WP216517B, P2167517BV, P2167517BVE, 2167517BV specifications

The Snapper P2167517BV is a highly efficient walk-behind lawn mower that epitomizes power and convenience in residential lawn care. This model is well-regarded for its robust design and cutting-edge technologies, making it a preferred choice for homeowners seeking a reliable mowing solution.

One of the standout features of the Snapper P2167517BV is its innovative design that combines durability with user-friendly operation. The mower is equipped with a powerful engine, which provides ample torque for tackling tough grass and challenging terrain. The self-propelled functionality allows users to effortlessly navigate their lawns without excessive manual effort, making the mowing experience much more enjoyable.

The P2167517BV is designed with a 21-inch steel cutting deck, which not only offers a wide cutting path for increased efficiency but also ensures longevity and resistance to wear. This mower supports multiple cutting heights, enabling users to adjust the blade position quickly. This versatility is perfect for maintaining different grass types and adapting to changing weather conditions.

In terms of technology, the Snapper P2167517BV incorporates a reliable electric start feature, eliminating the hassle of recoil starting. This system delivers reliable power at the push of a button, catering to users who value convenience and efficiency. The mower is also equipped with an exceptional bagging system that effectively collects clippings, promoting a clean lawn and simplifying post-mowing cleanup.

Another notable characteristic of the P2167517BV is its foldable handle design, which promotes easy storage while minimizing the space required. This feature is particularly appealing to those with limited storage areas.

In summary, the Snapper P2167517BV is a powerful and efficient lawn mower designed for residential use. Its combination of a durable steel cutting deck, robust engine performance, adjustable cutting heights, electric start, and superior grass collection technology makes it an ideal choice for homeowners. The emphasis on user-friendliness and storage convenience further enhances its appeal, cementing its status as one of the leading models in its category. Whether tackling a small yard or a larger expanse, the Snapper P2167517BV promises reliability, performance, and an exceptional mowing experience.
Top Page Image Contents