Snapper RD Series, 2400 XL Series manual Troubleshooting the Mower

Page 29

Troubleshooting, Adjustment, & Service

Tractor Troubleshooting Continued

Tractor drive belt slips.

1.

Pulleys or belt greasy or oily.

Clean as required.

 

2.

Belt stretched or worn.

Replace with new belt.

 

3.

Idler pulley pivot bracket

Remove idler pulley bracket, clean and lubricate.

 

 

“frozen” in declutched position.

 

 

 

 

 

Brake will not hold.

1.

Brake is incorrectly adjusted.

See Brake Adjustment.

 

2.

Internal brake worn.

See your dealer.

 

 

 

 

Tractor steers hard or

1.

Steering linkage is loose.

Check and tighten any loose connections.

handles poorly.

 

 

See Steering Gear Adjustment.

 

2.

Improper tire inflation.

Check and correct.

 

3.

Front wheel spindle

Grease spindles. See Lubricating the

 

 

bearings dry.

Tractor.

 

 

 

 

TROUBLESHOOTING THE MOWER

PROBLEM

CAUSE

REMEDY

Mower will not raise.

1.

Lift linkage not properly attached

Attach or repair.

 

 

or damaged.

 

 

 

 

 

Mower cut is uneven.

1.

Mower not leveled properly.

See Mower Adjustment.

 

2.

Tractor tires not inflated

See Maintenance Section.

 

 

equally.

 

 

 

 

 

Mower cut is rough looking.

1.

Engine speed too slow.

Set to full throttle.

 

2.

Ground speed too fast.

Slow down.

 

3.

Blades are dull.

Replace blades.

 

 

 

See Mower Blade Service.

 

4.

Mower drive belt slipping

Clean or replace belt as necessary.

 

 

because it is oily or worn.

 

 

5.

Check PTO (Electric Clutch)

See Adjustments Section.

 

 

Adjustment.

 

 

6.

Blades not properly fastened

See Servicing the Mower Blades.

 

 

to arbors.

 

 

 

 

 

Engine stalls easily with

1.

Engine speed too slow.

Set to full throttle.

mower engaged.

2.

Ground speed too fast.

Slow down.

 

3.

Carburetor improperly adjusted.

See Engine Manual.

 

4.

Cutting height set too low.

Cut tall grass at maximum cutting

 

 

 

height during first pass.

 

5.

Discharge chute jamming

Cut grass with discharge pointing toward

 

 

with cut grass.

previously cut area.

 

6.

Engine not up to operating

Run engine for several minutes to warm-up.

 

 

temperature.

 

 

7.

Starting mower in tall grass.

Start the mower in a cleared area.

 

 

 

 

Excessive mower vibration.

1.

Blade mounting screws

Tighten to 45-55 ft.lbs. (61-75 N.m.).

 

 

are loose.

 

 

2.

Mower blades, arbors,

Check and replace as necessary.

 

 

or pulleys are bent.

 

 

3.

Mower blades are out

Replace blades.

 

 

of balance.

See Servicing the Mower Blades.

 

4.

Belt installed incorrectly.

Reinstall Correctly.

 

 

 

 

Excessive belt wear or breakage.

1.

Bent or rough pulleys.

Repair or replace.

 

2.

Using incorrect belt.

Replace with correct belt.

 

 

 

 

Mower drive belt slips

1.

Idler pulley spring broken or not

Repair or replace as needed.

or fails to drive.

 

properly attached.

 

 

2.

Belt stops out of adjustment.

Check belt stops.

 

3.

Mower drive belt broken.

Replace drive belt.

 

4.

PTO clutch out of adjustment.

Adjust PTO clutch.

 

 

 

 

Mower blades out of time.

1.

Drive belt tension incorrect.

Perform mower belt tension check.

 

2.

Shear pin broken.

Replace.

27

Page 28 Page 30
Image 29
Page 28 Page 30
Contents 20HP Hydro Tractors 18HP Hydro Tractors Mower DecksPage Table of Contents Safety Rules & Information Operating Safety Slope Operation Safety Rules and InformationGeneral Operation Safety Rules & InformationIgnition System Safe Handling of Gasoline Service & MaintenanceCE Models Identification NumbersCE Identification TAG Markings Safety Decals Safety DecalsDecal Cutting Height Decal Transmission Release Decal Ignition PositionsOperational Safety Checks Safety IconsControl Functions Features & Controls Stopping the Tractor & Engine General Operating SafetyAdding Fuel Operating the Tractor Emptying the Catcher Parking Brake FunctionStorage Attaching a TrailerMuffler and surrounding areas may be hot Mower Deck Removal InstallationRemoving the Mower Deck Installing the Mower Deck Catcher Removal InstallationInstall Mulch Plug Discharge Mulch Plug Installation & Removal Some ModelsPage Fall Before Every SpringTransmission Maintenance Regular MaintenanceBattery Maintenance Check Tire PressuresOil LubricationLubricate Rear Axle Shafts Service Interval Yearly4x4 Wood Block Servicing the Mower BladesCheck Mower Blade Timing PTO Clutch Adjustment Check Safety Interlock System CheckEngine Maintenance SET Mower Belt TensionTroubleshooting, Adjustments, & Service Troubleshooting the Mower Hopper Latch Adjustment Seat AdjustmentPitch Adjustment Seat Slide AdjustmentBrake Adjustment Steering Gear AdjustmentAdjustment Nut NutsCATCHER-FULL Alarm Adjustment Troubleshooting, Adjustment, & ServiceMower Lift Adjustment Battery ChargingAdjust PTO Clutch Window Adjustment Nut Feeler Gauge PTO Clutch AdjustmentTransmission Release Lever Transmission PurgingLeveling The Mower Mower AdjustmentsCutting Height Adjustment Arbor Drive Belt Replacement PTO Belt ReplacementEngine DimensionsTransmission ChassisMaintenance Items Replacement PartsOptional Accessories Technical ManualsPage O D U C T S

RD Series, 2400 XL Series specifications

The Snapper 2400 XL Series and RD Series represent the pinnacle of outdoor power equipment, embodying a perfect blend of performance, durability, and user-friendly design. Engineered for both residential and commercial applications, these models are specifically crafted to cater to a wide range of mowing needs.

The Snapper 2400 XL Series, known for its robust construction, features a powerful engine that delivers exceptional performance and reliability. With a cutting deck size that varies, users can choose options ranging from 21 inches to 30 inches, ensuring versatility for different yard sizes and conditions. This series utilizes a patented rear-engine design which provides superior visibility and maneuverability, making it ideal for navigating tight spots and landscaping around obstacles.

One of the standout technologies in the 2400 XL Series is the Instant Response Transmission. This system allows for smooth acceleration and responsive steering, which enhances user control. Additionally, the mowers are equipped with an adjustable cutting height feature, allowing for precision mowing to accommodate varying grass types and conditions.

Transitioning to the RD Series, it boasts a unique dual-blade system that enhances cutting efficiency. The dual blades create finer clippings, which decompose faster, resulting in healthier grass. The RD Series is designed with heavy-duty wheels and a reinforced steel frame, ensuring it can handle the rigors of challenging terrains while maintaining stability and control.

Both series highlight Snapper's commitment to comfort and user experience. Each model is ergonomically designed with comfortable grips and adjustable seating, reducing fatigue during extended mowing sessions. Moreover, the easy-start engine technology ensures that users can get to work without fuss, even in cold weather conditions.

Durability is a key characteristic of both the 2400 XL and RD Series. Constructed with high-quality materials, including corrosion-resistant surfaces, these mowers are built to withstand the elements and provide long-lasting performance. With exceptional warranty options, users can rest assured knowing their investment is protected.

In summary, the Snapper 2400 XL Series and RD Series incorporate advanced technologies and features designed to enhance mowing efficiency, comfort, and durability. With a focus on performance and ease of use, these mowers are ideal for homeowners and landscaping professionals alike, ensuring a clean, precise cut season after season. Users can confidently choose Snapper for their outdoor power equipment needs, knowing they are backed by a brand renowned for innovation and quality.
Top Page Image Contents