Snapper EP217018BV, ERP217018BV, ERP217018BV, EP217018BV Recycling Operation

Page 11

Section 2 - OPERATING INSTRUCTIONS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

2.10INSTALLATION of DISCHARGE DEFLECTOR (Optional accessory on some models)

Install discharge deflector if discharging is desired. Grass Bag and Bag Adapter or Recycling Cover must be removed.

1.Remove front and rear nuts that secure Bag Adapter or Recycling Cover to deck. Refer to sections concerning these parts.

2.Install discharge deflector and secure to deck using hardware removed in Step 1. Slot in front edge of discharge deflector must be under nut as shown and both bolts protruding through holes in the side of the deflector. Secure nuts to the side of deflector. Tighten nuts securely. See Figure 2.17.

INSTALL

 

SLIDE

DISCHARGE

 

DEFLECTOR

DEFLECTOR

 

SLOT

 

 

 

INSTALL

NUTS

FIGURE 2.17

2.11INSTALLATION of RECYCLING COVER (Optional Accessory on Some Models)

It will be necessary to remove bag adapter and grass bag or discharge deflector before installing recycling cover. See previous section for instructions. Install the recycling cover and secure to the side and top of the deck with the two nuts provided on the machine. Slide top portion of cover under nut secured to the deck. See Figure 2.18.

RECYCLING

COVER

INSTALL RECYCLING

COVER TO THE DECK

USING THE TWO NUTS

FIGURE 2.18

2.12 RECYCLING OPERATION

NOTE: For best recycling results, cut up to a maximum of 1/3 of grass blade length and recycle ONLY when grass is dry.

1.Set all wheels in the highest cutting position (Notch 6).

2.Move engine speed control to “FAST” (Rabbit) position.

3.Move ground speed control to slowest speed setting.

4.Proceed mowing slowly. If grass is very dense, lower each rear wheel latch one notch lower than the front wheel latches to improve recycling performance.

WARNING

DO NOT operate without entire Grass Catcher or guard in place. Grass Catcher components are subject to deterioration during normal use. Inspect frequently and replace worn or damaged components immediately.

WARNING

Grass Catcher bags used on SNAPPER products are made of woven fabric, and are subject to deterioration and wear during normal usage. Check condition of bag before each use. Immediately replace worn or damaged catcher bags with only bags recommended by SNAPPER. The grass catcher is optional equipment on some models.

11

Image 11
Contents Series Designation Engine Horse PowerEngine Designation Important Safety Instructions From Previous Column From PreviousDo not refuel the machine indoors Important Safety Instructions Table of Contents Nomenclature Engine SpeedControl IntroductionStarting & Operation Engine & Blade PRE-START Check ListStopping Handle Height AdjustmentCutting Height Adjustment Propelling MowerInstallation of Grass BAG Door Type Bag Connector Adapter Flange Recycling Operation Important Drain fuel tank before tipping mower Service After First 5 Hours 3.2.1. Change Engine OILDispose of drain oil properly Check Engine Drive Belt Service AnnuallyStorage Procedure Check Mower Blade1.A. Ninja Blade Wear Limit Mower Blade Replacement Standard Blade Wear LimitBlade Sharpening Wheel Drive Control Adjustment Driven Disc Adjustment Driven and Drive Disc ServiceCleaning Drive Disc & Driven Disc Drive Spring Repair/ReplacementOn Next Replacing Rubber Driven Disc Repair & Adjustments On Next Belt ServiceEngine Drive Belt Replacement Stretch Type Belts Pulley Position Reinstall blade hub and cutter bladeCorrective Action Problem Probable CauseUSE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts 100Decal Identification European Performance Disclaimer of Warranty Year Limited WarrantyPage Page European Steel Deck Walk Behind Mowers Series