Snapper LT145H33GBV Blade Belt Adjustment 33 Deck, Blade Belt Adjustment 38 Deck, On next

Page 18

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. If deck front to rear level is not correct, this could cause blade belt problems.

4.2.2.BLADE BELT ADJUSTMENT – 33” DECK

1.Move tractor to a firm, level surface.

2.Turn engine "OFF". Remove key.

3.Move blade engagement lever down to "OFF". See Figure 4.2.

4.Place deck in mid cutting position.

5.Check front to rear level. Refer to Section “33 DECK LEVEL ADJUSTMENT (FRONT TO REAR)”.

MOVE BLADE

ENGAGEMENT

LEVER TO “OFF”

FIGURE 4.2

IMPORTANT: If deck front to rear level is not correct, this could cause blade belt problems.

6.Move blade engagement lever to "ON".

7.Measure blade cable extension spring. The length of the spring (x) should increase by 1” (+/-1/8”). See Figure

BLADE CABLE

EXTENSION

SPRING

X

X + 1” +/- 1/8”

8.(33" Deck) To adjust tension, remove extension rod mounting bolt and nut. See Figure 4.4.

9.Move extension rod to next hole towards rear of deck and secure with mounting bolt and nut.

10.Measure extension spring with blade engagement lever in the "ON" and "OFF" positions. See Figure 4.3. Continue adjustment until tension is correct.

IMPORTANT: Blade brake function must be verified after performing blade belt adjustment.

11.Check blade brake. Refer to Section “CHECK BLADE BRAKE”. Blades must stop rotating in 5 seconds or less when turned off.

LEAST TENSION

MOST TENSION

EXTENSION

ROD

MOUNTING

NUT & BOLT

FIGURE 4.4

4.2.3.BLADE BELT ADJUSTMENT – 38” DECK

The blade belt on the 38” deck requires no tension adjustment. If the belt becomes worn or damaged it must be replaced. Refer to Section “BLADE BELT REMOVAL &

REPLACEMENT”.

4.2.4.ADJUSTING MOWER BLADE – 33” DECK (33" Decks Only; no adjustment for 38")

1.Select a point on the deck and mark for reference.

2.Mark blade tips as “A” and “B”.

3.Rotate blade until blade tip “A” is at deck reference mark

4.Measure the distance between deck lip and blade tip. Note the measurement. See Figure 4.5.

(Continued on next page)

FIGURE 4.3

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Lawn Tractor Hydrostatic Drive Series G Model Number ExplanationImportant Safety Instructions Operation Table of Contents Components ControlsPRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine OFFStarting & Operation 2.3.2. Starting Wheel Drive Starting Mower BladeStopping Wheel Drive Stopping Stopping Mower Blade Setting Park BrakeCutting Height Adjustment Releasing Park BrakeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideChange Engine OIL Service After First 5 HoursIntroduction Check Blade BrakeCheck 33 Deck Drive Belt Service Every 25 Operating HoursCheck Engine Check 38 Deck Drive BeltTractor Lubrication Service Annually Fuel FilterService Annually 3.4.2. Fuel Filter From PreviousSpark Plug Hydrostatic Transmission OIL Engine Adjustments & Repair Blade Brake AdjustmentDeck Blade Brake Adjustment Blade Belt Adjustment 33 Deck Blade Belt Adjustment 38 DeckOn next Adjusting Mower Blade 33 Deck from previous Side View of DeckDeck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Sector PlatesDeck Level Adjustment Front to Rear Front Lift ROD Front of Tractor Deck Level Adjustment Front to Rear Tractor Drive Components 4.3.1. Brake AdjustmentRear to Front View of Deck Steering Adjustment Shifter AdjustmentMounting Standard Blade Sharpening Mower Blade Service Standard Blade Wear LimitsNinja Blade Wear Limits Ninja Blade SharpeningMower Blade Replacement Traction Drive Belt Replacement Mower Deck RemovalTraction drive belt removal Traction drive belt replacement View from Underneath TractorDeck Drive Belt Battery Service Battery Battery RemovalBattery Installation Battery StorageBattery Testing NEW Battery PreparationAvailable Accessories Schematic Wiring Harness P.N Schematic Wiring Harness P.N LT15OHGKVLT145H33GBV & LT145H38 GBV Troubleshooting Guide Troubleshooting Guide LT145H33GBV Tractor Drive Belts Mower BladesNinja LT145H38GBVYear Limited Warranty Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Lawn Tractor Hydrostatic Drive Series G

LT145H33GBV, LT145H33GBV, LT145H38GBV, LT150H38GKV specifications

The Snapper LT145H33GBV, LT145H38GBV, LT150H38GKV, and LT145H33GBV represent a series of innovative lawn tractors designed for efficiency, comfort, and durability. These models are tailored for homeowners seeking an effective solution for lawn care, offering a blend of performance and features that set them apart from traditional lawn mowing equipment.

One prominent feature of these tractors is their powerful engines. The LT145H33GBV and LT145H38GBV are equipped with 14.5 HP engines, while the LT150H38GKV sports a more robust 15 HP engine, allowing for higher performance and more demanding tasks. These engines are designed for reliability and longevity, ensuring they can handle various terrains with ease.

Each model is designed with user comfort in mind. The seats are ergonomically designed for prolonged use, featuring adjustable settings to ensure a personalized fit. Additionally, the tractors have easy-to-reach controls, a smooth steering mechanism, and ample legroom, making the mowing experience more enjoyable.

The cutting systems of these Snapper models are notable for their versatility. With a wide cutting deck size of up to 42 inches in the LT145H33GBV and LT145H38GBV, and a slightly larger 50-inch option in the LT150H38GKV, they provide the capability to mow larger areas efficiently. The adjustable cutting heights allow users to customize their lawns' appearance, ensuring the right height for various grass types and conditions. Furthermore, the deck is designed for easy cleaning and maintenance, which prolongs the life of the equipment.

Another key characteristic of these lawn tractors is their innovative technologies. Many models feature Snapper's patented rear-engine design, which enhances visibility and maneuverability. This design reduces the turning radius, allowing for easy navigation around flower beds, trees, and other obstacles in the yard.

Fuel efficiency is a critical factor, and these tractors do not disappoint. They are engineered to optimize fuel consumption while delivering high performance, ensuring that users can maximize their mowing time without frequent refueling.

Safety remains a priority in the design of Snapper lawn tractors. Each model is equipped with safety features such as a seat belt and a safety switch that automatically shuts off the engine if the operator leaves the seat, preventing accidents.

In summary, the Snapper LT145H33GBV, LT145H38GBV, LT150H38GKV, and LT145H33GBV are designed to deliver exceptional performance paired with user comfort and safety. With powerful engines, versatile cutting systems, and innovative features, these tractors are solid choices for homeowners looking to maintain their lawns effortlessly and effectively.
Top Page Image Contents