Snapper LT145H33GBV, LT145H38GBV, LT150H38GKV Battery Testing, NEW Battery Preparation

Page 31

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT OVERFILL! DO NOT attempt to service or charge the battery while it is installed on the machine. DO NOT use “BOOST” chargers on the battery.

4.5.5.BATTERY TESTING

There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current. To perform unloaded testing, check charge condition using either a hydrometer or voltmeter.

1.Using a voltmeter, voltage readings appear instantly to show the state of charge. Remember to hook the positive lead to the battery’s positive terminal, and the negative lead to the negative terminal.

2.A hydrometer measures the specific gravity of each cell. The specific gravity tells the degree of charge; generally, a specific gravity of about 1.265 to 1.280 indicates full charge. A reading of 1.230 to 1.260 indicates the battery should be charged. The chart on the next page shows the charge level as measured by syringe float hydrometer, digital voltmeter and five ball hydrometer.

4.5.6NEW BATTERY PREPARATION

1.Remove battery from carton.

2.Place battery in a well ventilated area on a level non- concrete surface.

3.Remove battery cell caps. Fill cells as required with electrolyte (purchased separately) to proper level. Fill to 3/16” above cell plates. Filling battery with electrolyte will bring the battery to 80% charged state.

4.5.7. BATTERY TESTING

4.With cell caps removed, connect battery charger to battery terminals; RED to positive (+) and BLACK to negative (-) terminal.

IMPORTANT: 3/16” above cell plates is the recommended level. However do not try to measure this dimension. Never place anything in battery other than specified electrolyte.

5.Slow charge the battery at 1 amp for 2 hours to bring the battery to full charge.

6.After charging, check level of electrolyte and add as needed to bring level to 3/16” above cell plates.

7.Reinstall cell caps.

8.Slide battery partially into battery housing.

9.Connect positive (+) cable (red) first, from wiring harness to the positive terminal (+) on battery using bolt and nut provided in hardware bag. Connect negative (-) cable (black) last, to negative terminal (-) on battery using bolt and nut. Apply a small amount of grease over terminals to prevent corrosion.

10.Insert battery completely into battery housing.

11.Reinstall seat assembly.

WARNING

Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal, which could cause sparks. Cables must be connected to battery terminals in the proper position. RED (Positive) cable must go to the ( + ) terminal. BLACK (Negative) cable must go to the ( - ) terminal.

Battery Condition Chart

 

State of Charge

Syringe Hydrometer

Digital Voltmeter

Five Ball Hydrometer

100%

Charged w/ Sulfate Stop

1.280

12.80v

Five Balls Floating

100%

Charged

1.265

12.60v

Four Balls Floating

75% Charged

1.210

12.40v

Three Balls Floating

50% Charged

1.160

12.10v

Two Balls Floating

25% Charged

1.120

11.90v

One Ball Floating

0% Charged

Less than 1.100

Less than 11.80v

Zero Balls Floating

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Model Number Explanation Lawn Tractor Hydrostatic Drive Series GImportant Safety Instructions Operation Table of Contents Controls ComponentsOPERATOR’S Seat Adjustment Front to Rear Adjustment PRE-START ChecklistOFF Starting & Operation Starting EngineStarting Mower Blade Starting & Operation 2.3.2. Starting Wheel DriveStopping Wheel Drive Releasing Park Brake Setting Park BrakeCutting Height Adjustment Stopping Stopping Mower BladeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Override Reverse Lockout MechanismCheck Blade Brake Service After First 5 HoursIntroduction Change Engine OILCheck 38 Deck Drive Belt Service Every 25 Operating HoursCheck Engine Check 33 Deck Drive BeltTractor Lubrication Fuel Filter Service AnnuallyFrom Previous Service Annually 3.4.2. Fuel FilterSpark Plug Hydrostatic Transmission OIL Blade Brake Adjustment Engine Adjustments & RepairDeck Blade Brake Adjustment Blade Belt Adjustment 38 Deck Blade Belt Adjustment 33 DeckOn next Side View of Deck Adjusting Mower Blade 33 Deck from previousDeck Level Adjustment Front to Rear Sector Plates Deck Level Adjustment Side to SideDeck Level Adjustment Front to Rear Front Lift ROD Front of Tractor Tractor Drive Components 4.3.1. Brake Adjustment Deck Level Adjustment Front to RearRear to Front View of Deck Shifter Adjustment Steering AdjustmentMounting Ninja Blade Sharpening Mower Blade Service Standard Blade Wear LimitsNinja Blade Wear Limits Standard Blade SharpeningTraction Drive Belt Replacement Mower Deck Removal Mower Blade ReplacementTraction drive belt removal View from Underneath Tractor Traction drive belt replacementDeck Drive Belt Battery Storage Battery Battery RemovalBattery Installation Battery ServiceNEW Battery Preparation Battery TestingAvailable Accessories Schematic Wiring Harness P.N LT15OHGKV Schematic Wiring Harness P.NLT145H33GBV & LT145H38 GBV Troubleshooting Guide Troubleshooting Guide LT145H38GBV Tractor Drive Belts Mower BladesNinja LT145H33GBVYear Limited Warranty Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Lawn Tractor Hydrostatic Drive Series G

LT145H33GBV, LT145H33GBV, LT145H38GBV, LT150H38GKV specifications

The Snapper LT145H33GBV, LT145H38GBV, LT150H38GKV, and LT145H33GBV represent a series of innovative lawn tractors designed for efficiency, comfort, and durability. These models are tailored for homeowners seeking an effective solution for lawn care, offering a blend of performance and features that set them apart from traditional lawn mowing equipment.

One prominent feature of these tractors is their powerful engines. The LT145H33GBV and LT145H38GBV are equipped with 14.5 HP engines, while the LT150H38GKV sports a more robust 15 HP engine, allowing for higher performance and more demanding tasks. These engines are designed for reliability and longevity, ensuring they can handle various terrains with ease.

Each model is designed with user comfort in mind. The seats are ergonomically designed for prolonged use, featuring adjustable settings to ensure a personalized fit. Additionally, the tractors have easy-to-reach controls, a smooth steering mechanism, and ample legroom, making the mowing experience more enjoyable.

The cutting systems of these Snapper models are notable for their versatility. With a wide cutting deck size of up to 42 inches in the LT145H33GBV and LT145H38GBV, and a slightly larger 50-inch option in the LT150H38GKV, they provide the capability to mow larger areas efficiently. The adjustable cutting heights allow users to customize their lawns' appearance, ensuring the right height for various grass types and conditions. Furthermore, the deck is designed for easy cleaning and maintenance, which prolongs the life of the equipment.

Another key characteristic of these lawn tractors is their innovative technologies. Many models feature Snapper's patented rear-engine design, which enhances visibility and maneuverability. This design reduces the turning radius, allowing for easy navigation around flower beds, trees, and other obstacles in the yard.

Fuel efficiency is a critical factor, and these tractors do not disappoint. They are engineered to optimize fuel consumption while delivering high performance, ensuring that users can maximize their mowing time without frequent refueling.

Safety remains a priority in the design of Snapper lawn tractors. Each model is equipped with safety features such as a seat belt and a safety switch that automatically shuts off the engine if the operator leaves the seat, preventing accidents.

In summary, the Snapper LT145H33GBV, LT145H38GBV, LT150H38GKV, and LT145H33GBV are designed to deliver exceptional performance paired with user comfort and safety. With powerful engines, versatile cutting systems, and innovative features, these tractors are solid choices for homeowners looking to maintain their lawns effortlessly and effectively.
Top Page Image Contents