Snapper LT145H33GBV Deck Level Adjustment Front to Rear, Rear to Front View of Deck

Page 22

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.2.9.38" DECK LEVEL ADJUSTMENT (FRONT TO REAR)

1.Position the blades as shown. See Figure 4.16.

FRONT OF TRACTOR

LEFT FRONT

BLADE TIP

RIGHT REAR BLADE TIP

FIGURE 4.16

2.Measure the distance from the left front blade tip to the ground and from the right rear blade tip to the ground. The front left blade tip should be between 1/8" and 3/8" higher than the right rear (factory setting). If it is between 1/8" and 3/8" you are finished with adjustment.

3.If it is not within specifications, adjust by raising or lowering the front of the deck using the swivel on the front lift rod. Turning the swivel clockwise will raise the front of the deck. Turning the swivel counterclockwise will lower the front of the deck.

NOTE: The deck should be set so that the rear of the deck is 1/4" lower than the front. See Figure 4.17.

REAR TO FRONT VIEW OF DECK

 

X

X - 1/8”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ANGLE IRON

FIGURE 4.17

4.3TRACTOR DRIVE COMPONENTS 4.3.1. BRAKE ADJUSTMENT

When adjusted properly, the brake should stop the tractor in approximately 6 feet or less from top speed. Drive the machine at maximum forward speed and apply the brake. If stopping distance is greater than 6 feet, brake adjustment is required.

1.Turn engine “OFF”. Remove key.

2.Locate brake adjustment nut underneath the left side at the rear of tractor. See Figure 4.18.

3.Turn nut 1 turn clockwise to increase braking action. DO NOT over tighten brake adjustment.

4.Start engine and test brake.

5.Continue adjustment as described above until proper brake function is achieved.

ROTATE ADJUSTING NUT CLOCKWISE TO

INCREASE BRAKING OR COUNTER

CLOCKWISE TO DECREASE BRAKING

FIGURE 4.18

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Lawn Tractor Hydrostatic Drive Series G Model Number ExplanationImportant Safety Instructions Operation Table of Contents Components ControlsPRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine OFFStarting Mower Blade Starting & Operation 2.3.2. Starting Wheel DriveStopping Wheel Drive Stopping Stopping Mower Blade Setting Park BrakeCutting Height Adjustment Releasing Park BrakeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideChange Engine OIL Service After First 5 HoursIntroduction Check Blade BrakeCheck 33 Deck Drive Belt Service Every 25 Operating HoursCheck Engine Check 38 Deck Drive BeltTractor Lubrication Service Annually Fuel FilterFrom Previous Service Annually 3.4.2. Fuel FilterSpark Plug Hydrostatic Transmission OIL Blade Brake Adjustment Engine Adjustments & RepairDeck Blade Brake Adjustment Blade Belt Adjustment 38 Deck Blade Belt Adjustment 33 DeckOn next Adjusting Mower Blade 33 Deck from previous Side View of DeckDeck Level Adjustment Front to Rear Sector Plates Deck Level Adjustment Side to SideDeck Level Adjustment Front to Rear Front Lift ROD Front of Tractor Tractor Drive Components 4.3.1. Brake Adjustment Deck Level Adjustment Front to RearRear to Front View of Deck Steering Adjustment Shifter AdjustmentMounting Standard Blade Sharpening Mower Blade Service Standard Blade Wear LimitsNinja Blade Wear Limits Ninja Blade SharpeningMower Blade Replacement Traction Drive Belt Replacement Mower Deck RemovalTraction drive belt removal Traction drive belt replacement View from Underneath TractorDeck Drive Belt Battery Service Battery Battery RemovalBattery Installation Battery StorageBattery Testing NEW Battery PreparationAvailable Accessories Schematic Wiring Harness P.N LT15OHGKV Schematic Wiring Harness P.NLT145H33GBV & LT145H38 GBV Troubleshooting Guide Troubleshooting Guide LT145H33GBV Tractor Drive Belts Mower BladesNinja LT145H38GBVYear Limited Warranty Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Lawn Tractor Hydrostatic Drive Series G

LT145H33GBV, LT145H33GBV, LT145H38GBV, LT150H38GKV specifications

The Snapper LT145H33GBV, LT145H38GBV, LT150H38GKV, and LT145H33GBV represent a series of innovative lawn tractors designed for efficiency, comfort, and durability. These models are tailored for homeowners seeking an effective solution for lawn care, offering a blend of performance and features that set them apart from traditional lawn mowing equipment.

One prominent feature of these tractors is their powerful engines. The LT145H33GBV and LT145H38GBV are equipped with 14.5 HP engines, while the LT150H38GKV sports a more robust 15 HP engine, allowing for higher performance and more demanding tasks. These engines are designed for reliability and longevity, ensuring they can handle various terrains with ease.

Each model is designed with user comfort in mind. The seats are ergonomically designed for prolonged use, featuring adjustable settings to ensure a personalized fit. Additionally, the tractors have easy-to-reach controls, a smooth steering mechanism, and ample legroom, making the mowing experience more enjoyable.

The cutting systems of these Snapper models are notable for their versatility. With a wide cutting deck size of up to 42 inches in the LT145H33GBV and LT145H38GBV, and a slightly larger 50-inch option in the LT150H38GKV, they provide the capability to mow larger areas efficiently. The adjustable cutting heights allow users to customize their lawns' appearance, ensuring the right height for various grass types and conditions. Furthermore, the deck is designed for easy cleaning and maintenance, which prolongs the life of the equipment.

Another key characteristic of these lawn tractors is their innovative technologies. Many models feature Snapper's patented rear-engine design, which enhances visibility and maneuverability. This design reduces the turning radius, allowing for easy navigation around flower beds, trees, and other obstacles in the yard.

Fuel efficiency is a critical factor, and these tractors do not disappoint. They are engineered to optimize fuel consumption while delivering high performance, ensuring that users can maximize their mowing time without frequent refueling.

Safety remains a priority in the design of Snapper lawn tractors. Each model is equipped with safety features such as a seat belt and a safety switch that automatically shuts off the engine if the operator leaves the seat, preventing accidents.

In summary, the Snapper LT145H33GBV, LT145H38GBV, LT150H38GKV, and LT145H33GBV are designed to deliver exceptional performance paired with user comfort and safety. With powerful engines, versatile cutting systems, and innovative features, these tractors are solid choices for homeowners looking to maintain their lawns effortlessly and effectively.
Top Page Image Contents