Snapper SPE131KW, SPE151KW, SPE361, SPE381 Reverse Operation, Stopping Machine

Page 13

SECTION 3 - OPERATING INSTRUCTIONS

3.5 STARTING & OPERATING

(Continued from previous page)

13.STOPPING MACHINE

Simultaneously squeeze both Traction Levers firmly against the handle and hold. Pull both the right and left Traction Locks rearward with index fingers until both Traction Levers are locked in the Traction Locked position.

14.Pull the Blade Clutch Switch rearward to the OFF position. See Figure 3.7.

BLADE CLUTCH

SWITCH SHOWN

IN OFF POSITION

BLADE

CLUTCH

SWITCH

FIGURE 3.7

15.

Place the Transmission Shift Lever into the

 

NEUTRAL (N) position.

16.

Move engine speed control to slow (Turtle)

 

position.

17.

Stop engine. Turn key switch to “Stop” position.

WARNING

DO NOT operate blades in reverse. Stop blades. LOOK and SEE behind and down for children, pets and hazards before and while backing. Engine speed must be set to SLOW before operating in reverse.

3.6 REVERSE OPERATION

3.6.1.TO REVERSE DIRECTION

1.To REVERSE DIRECTION OF MACHINE, STOP Machine and lock Traction Levers.

2.Pull Blade Clutch Switch rearward to the OFF position. Move Engine Speed Control Lever to slow (turtle) position.

3.Move Transmission Shift Lever to REVERSE (R) position.

4.Hold Operator’s Presence Control (OPC) against handlebar.

5.To START MACHINE MOVEMENT, simultaneously squeeze both Traction Levers firmly against the handle allowing the right and left Traction Locks to release.

6.Using caution, simultaneously and slowly release both Traction Levers. The machine will begin to move in reverse.

7.To STOP forward or reverse motion, firmly squeeze both Traction Levers towards the handle and hold. Using your index fingers, pull right and left Traction Locks back until both Traction Levers lock in Traction Locked position. See Figure 3.8.

1.SQUEEZE TRACTION LEVERS

2.PULL TRACTION LOCKS

Remove key. See Figure 2.1.

WARNING

DO NOT leave machine with engine running. Stop engine. Stop blades. Lock Traction Levers. Remove key. DO NOT park machine on slopes.

1

REARWARD TO LOCK

2

TRACTION LOCK

TRACTION LEVER

(RIGHT HAND - RELEASED POSITION SHOWN)

FIGURE 3.8

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model Number Explanation PRO Gear Express Walk Behind Mowers MID-SIZE SeriesProtection for Children Important Safety InstructionsSlope Operation PreparationOperation Safe Handling of GasolineMaintenance Table of Contents Introduction FamiliarizationNomenclature Keep Children and Others OUT of the Mowing Area Safety Messages and SymbolsImportant Safety and Operating Instructions Controls Operating Instructions Safety Interlock System ChecksBefore Operating Stopping MachineStarting & Operating PRE-START Check ListEngine Start Engine AS Follows On next Stopping Machine Reverse OperationTo Reverse Direction Turning Mower Traction Lock OperationMowing and Turning on Hillsides Adjusting Caster Wheels Cutting Height AdjustmentAdjusting Blade on Cutter Spindle Side Profile of Unit Adjusting Fixed Deck AttachmentSymptom Problem Solution TroubleshootingHours Procedure Comments Mower TroubleshootingSTEERING/BRAKES AdjustmentsTraction LEVERS/RODS Handle Height Transmission Shift Lever AdjustmentReplacement Parts Power Unit ServiceTransmission Parts & Service Transmission Belt REMOVAL/REPLACEMENT Mower Attachment ServiceTraction Belt Removal & Replacement Cutter Deck Belt Removal & InstallationStandard Replacement Blades Cutting Blade ServiceBlade Removal and Sharpening Remove spindle pulley from spindle shaft Kawasaki Engine only ElectricalElectric Clutch Yellow Black Blue Engine 15A Fuse Disclaimer of Warranty Year Limited WarrantySnapper Product Registration Form Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page PRO Gear Express MID-SIZE Walk Behind Mowers Series
Top Page Image Contents