Snapper SPE131KW, SPE151KW, SPE361, SPE381 Handle Height, Transmission Shift Lever Adjustment

Page 20

SECTION 5 - ADJUSTMENTS

5.3 HANDLE HEIGHT

The operator handle can be adjusted for operator comfort as follows:

1.Loosen the upper carriage bolt and nut on both sides of handlebar. See Figure 5.4.

2.Remove lower carriage bolt and nut on both sides of handlebar.

3.Raise or lower handlebar to desired height. See Figure 5.3.

4.Install the carriage bolt and nut in the lower hole in handlebar and securely tighten nut. See Figure 5.4.

5.Securely tighten the upper carriage bolt and nut.

6.After adjusting the handle height readjust traction links as described earlier. Shift rod (Connects the ground speed control lever and the transmission) will have to be readjusted.

7.Readjust traction levers/rods when handle height is changed.

*FACTORY SETTING UP

 

B

(4)

 

(3)

 

*(2)

DOWN

(1)

 

5.4TRANSMISSION SHIFT LEVER ADJUSTMENT

1.Disconnect the hair pin from shift rod that connects to the Transmission Shift lever. See Figure 5.5.

2.Move the Transmission Shift Lever to the neutral position. Move the shift lever, located on the transmission, to the neutral position.

3.Rotate the shift rod clockwise or counter clockwise to allow the upper portion of shift rod to be inserted into the ground speed control lever without moving the speed control lever or the Transmission Shift lever. Reinstall hair pin. See Figure 5.6.

TRANSMISSION

SHIFT

LEVER

DISCONNECT

SHIFT ROD

FROM THIS

POINT

SHIFT ROD

FIGURE 5.3

FIGURE 5.5

LOOSEN

RAISE

 

 

 

SHIFT

 

UPPER

 

SHIFT

CARRIAGE

 

LEVER

 

ROD

BOLT

 

 

 

 

 

 

LOWER

 

 

REMOVE

 

 

 

LOWER

 

 

 

CARRIAGE

 

 

 

BOLT

 

 

ROTATE

 

 

 

SHIFT

 

 

 

ROD

 

 

 

 

FIGURE 5.4

FIGURE 5.6

20

Image 20
Contents PRO Gear Express Walk Behind Mowers MID-SIZE Series Model Number ExplanationImportant Safety Instructions Protection for ChildrenSlope Operation PreparationSafe Handling of Gasoline OperationMaintenance Table of Contents Nomenclature FamiliarizationIntroduction Safety Messages and Symbols Keep Children and Others OUT of the Mowing AreaImportant Safety and Operating Instructions Controls Safety Interlock System Checks Operating InstructionsBefore Operating Stopping MachineEngine Start Engine AS Follows PRE-START Check ListStarting & Operating On next To Reverse Direction Reverse OperationStopping Machine Mowing and Turning on Hillsides Traction Lock OperationTurning Mower Adjusting Blade on Cutter Spindle Cutting Height AdjustmentAdjusting Caster Wheels Adjusting Fixed Deck Attachment Side Profile of UnitTroubleshooting Symptom Problem SolutionMower Troubleshooting Hours Procedure CommentsTraction LEVERS/RODS AdjustmentsSTEERING/BRAKES Transmission Shift Lever Adjustment Handle HeightTransmission Parts & Service Power Unit ServiceReplacement Parts Mower Attachment Service Transmission Belt REMOVAL/REPLACEMENTTraction Belt Removal & Replacement Cutter Deck Belt Removal & InstallationBlade Removal and Sharpening Cutting Blade ServiceStandard Replacement Blades Remove spindle pulley from spindle shaft Electrical Kawasaki Engine onlyElectric Clutch Yellow Black Blue Engine 15A Fuse Year Limited Warranty Disclaimer of WarrantySnapper Product Registration Form Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page PRO Gear Express MID-SIZE Walk Behind Mowers Series