Snapper SPE131KW, SPE151KW, SPE361, SPE381 Adjustments, Steering/Brakes, Traction LEVERS/RODS

Page 19

SECTION 5 - ADJUSTMENTS

5.1 STEERING/BRAKES

If machine is not as responsive as desired when either Traction Lever is squeezed, one or both brakes should be adjusted as follows:

1.Operate mower on level terrain with Transmission Shift Lever in No. 1 position. Determine which brake requires adjustment.

2.Stop engine, remove the key from switch and disconnect spark plug wire from spark plug. Secure wire away from plug.

3.Turn nut clockwise to increase brake tension. See Figure 5.1.

BRAKE ROD

MORE

TENSION

TURN

NUT

LESS

TENSION

BRAKE ARM

FIGURE 5.1

4.Place spark plug wire onto spark plug. Start engine and operate mower with transmission in the No. 1 position to check for proper adjustment. If further adjustment is required, follow all steps above.

5.2 TRACTION LEVERS/RODS

If the Traction Wheel Drive Belts become slack or new belts have been installed, it will be necessary to adjust the Traction Levers as follows:

1.Move the machine to a smooth, level surface and turn the engine OFF. Release the traction locks. Disconnect the Brake Rods from the Brake Arms. See Figure 5.1.

2.Remove the key from the switch, remove the spark plug wire from the spark plug and secure it away from the plug.

3.Shift the transmission to No. 1 position. Pull rearward hard on the Traction Levers. The space used to lock the Traction Locks should not bottom in the slot. Set the Traction Locks into the Locked position. The Idler Pulleys, Upper and Lower should

have completely declutched the belt. Release the Traction Locks and adjust as required.

4.Remove the hairpins from the traction rod adjustment blocks and remove the adjustment blocks from the traction links on each side of the mower. See Figure 5.2.

ROTATE

ADJUSTMENT

1/16” TO 1/8” BLOCKREMOVE HAIR PIN

GAP

BETWEEN

IDLER ARM

AND STUDS

IDLER

ARM

BELT

COVER

STUD

FIGURE 5.2

5.Rotate the adjustment block as required to make the idler arms almost touch against the belt cover studs when the Traction Levers are locked. There should be about 1/16” to 1/8” gap between the idler arms and studs. See Figure 5.2.

6.Reinstall the adjustment blocks and the hairpins. Check the settings as described above. Repeat as necessary.

7.Reassemble the Brake Rods to the Brake Arms with the hairpins removed earlier. Install belt covers.

8.Replace the Spark Plug Wire onto the Spark Plug. Start the mower according to the Safety Instructions and operate it to check the adjustments.

NOTE: It may be necessary to adjust the Traction Brakes after adjustment of the Traction Belts is complete.

9.If the belts continue to slip after properly adjusting Traction Rods, the transmission is mounted in slotted holes to provide additional tension adjustment. Remove transmission belt tension, loosen transmission bolts and slide transmission to back of slots. Tighten bolts securely and reinstall belt.

10.Adjust shift lever. Refer to Section “Transmission Shift Lever Adjustment”.

11.Repeat all Steps, 1 thru 8, after moving transmission.

WARNING

DO NOT attempt to operate machine without belt cover and studs secured into the proper position.

19

Image 19
Contents Model Number Explanation PRO Gear Express Walk Behind Mowers MID-SIZE SeriesPreparation Important Safety InstructionsProtection for Children Slope OperationOperation Safe Handling of GasolineMaintenance Table of Contents Introduction FamiliarizationNomenclature Keep Children and Others OUT of the Mowing Area Safety Messages and SymbolsImportant Safety and Operating Instructions Controls Stopping Machine Safety Interlock System ChecksOperating Instructions Before OperatingStarting & Operating PRE-START Check ListEngine Start Engine AS Follows On next Stopping Machine Reverse OperationTo Reverse Direction Turning Mower Traction Lock OperationMowing and Turning on Hillsides Adjusting Caster Wheels Cutting Height AdjustmentAdjusting Blade on Cutter Spindle Side Profile of Unit Adjusting Fixed Deck AttachmentSymptom Problem Solution TroubleshootingHours Procedure Comments Mower TroubleshootingSTEERING/BRAKES AdjustmentsTraction LEVERS/RODS Handle Height Transmission Shift Lever AdjustmentReplacement Parts Power Unit ServiceTransmission Parts & Service Cutter Deck Belt Removal & Installation Mower Attachment ServiceTransmission Belt REMOVAL/REPLACEMENT Traction Belt Removal & ReplacementStandard Replacement Blades Cutting Blade ServiceBlade Removal and Sharpening Remove spindle pulley from spindle shaft Kawasaki Engine only ElectricalElectric Clutch Yellow Black Blue Engine 15A Fuse Disclaimer of Warranty Year Limited WarrantySnapper Product Registration Form Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page PRO Gear Express MID-SIZE Walk Behind Mowers Series