Snapper NZM19483KWV, NZM27 613KH, NZM25523KWV, NZM25613KWV, NZM21523KWV Hydraulic SYSTEM, Purging

Page 13

Section 5 - ADJUSTMENTS & REPAIR

5.12HYDRAULIC SYSTEM, PURGING

After replacing or repairing hydraulic system components, one or both of the wheel drives may not pull properly. This is likely to be caused by air entrapped in the system. If you experience a pulling issue after completing repairs, perform the following procedure to purge the air from one or

both of the hydraulic drive systems.

IMPORTANT: WHEN REPLACING THE HYDRAULIC

FLUID FILTERS, PRE-FILL BOTH WITH OIL

(SAE 20W50 API SL) BEFORE INSTALLING. PRE-FILLING THE FILTERS WITH OIL WILL REDUCE OR POSSIBLY ELIMINATE THE NEED TO PURGE THE SYSTEM OF ENTRAPPED AIR

1.Locate hydraulic reservoir underneath operator's seat. After thoroughly cleaning the area around the top of the reservoir, remove filler cap. Bring fluid to proper level (1 ½" below the top of the filler neck). With engine off, add SAE 20W50 automotive oil. See Figure 4.6.

2.Open pressure relief valve on hydraulic pump, turning counter clockwise 2 full turns. See Figure

3.Carefully raise the rear of the machine so the wheels are off of the ground. Securely block the machine to prevent it from falling.

4.While seated in the operator's position, start the engine. Place engine speed control in FAST position.

5.Release parking brake and move motion

control levers out of the neutral lock position.

6.Slowly move motion control levers to the full forward and then to the full reward positions. Repeat this process 6 times.

7.Stop engine and wait for all rotation to stop before leaving the operator's position.

8.Close pressure relief valve on hydraulic pump, turning clockwise. Tighten snuggly.

9.With pressure relief valve closed, repeat Steps

4thru 7.

10.Remove blocks and lower rear of machine.

11.Check fluid level in reservoir. Add SAE 20W50 automotive oil as required to bring fluid level to 1 ½" from top of filler neck. Do Not over fill.

12.Install and tighten filler cap.

29

Page 12 Page 14
Image 13
Page 12 Page 14
Contents SNAPPER.coonough.,3o2os3 Parking Brake Lever Operation Wear Hearing Protection Safety Messages and SymbolsPull Switch UP to Roll Barprotectivestructuredecalsi PRE-START Check List Operating Instructions2, Stopping Machine Safety Interlock System ChecksFolding the Roll BAR Protective Structure Engine Must not Start ifAnnually END of Each Season Maintenance2. Fuel Filter Deck RemovalNeutral Position Adjustments Adjustments & RepairMower Deck Adjustment Levelness Neutral Position Adjustments Mower Deck & ComponentSection Traction Belt Tension Traction Belt ReplacementMower Drive Belt Replacement Tracking AdjustmentBelt Replacement Belt RemovalBearing Replacement Hydraulic SYSTEM, Purging SNAPPERo.coonouo

NZM21523KWV, NZM19483KWV, NZM25613KWV, NZM25523KWV, NZM27 613KH specifications

The Snapper NZM25523KWV, NZM25613KWV, NZM19483KWV, NZM21523KWV, and NZM27613KH are a series of innovative and high-performance lawn mowers designed to cater to the diverse needs of both residential and commercial users. These models showcase a range of cutting-edge features, technologies, and characteristics, making them stand out in the competitive outdoor power equipment market.

At the heart of these Snapper mowers is their powerful and efficient engine, designed to deliver robust performance while maintaining low emissions. The engines are paired with a reliable drivetrain, ensuring smooth self-propelling capabilities that significantly reduce the effort required for mowing large lawns. Users can select the desired mowing speed to suit their preferences and terrain, providing a customizable mowing experience.

One of the key features across these models is the innovative cutting system. Snapper mowers utilize a three-in-one cutting action, which allows for bagging, mulching, or side discharge of grass clippings. This versatility not only improves convenience but also empowers users to choose the best option for their specific lawn care needs. The finely engineered cutting deck design also ensures an even cut, enhancing the overall appearance of the lawn.

Durability is a hallmark of Snapper products. Each model features a heavy-duty steel construction and a robust deck that can withstand the rigors of frequent use. Users can expect these mowers to provide years of reliable service with minimal maintenance, thanks to their high-quality components and user-friendly design.

These mowers are also designed with ease of use in mind. Features such as an adjustable cutting height allow users to customize their mowing experience, ensuring optimal results for various grass types and conditions. Additionally, the ergonomic handles provide comfort during operation, reducing fatigue for the operator.

The Snapper NZM series also incorporates technological advancements such as easy-start systems for quick ignition and enhanced maneuverability. The compact design of these mowers promotes easy storage and transportability, making them an ideal choice for homeowners with limited space.

In summary, the Snapper NZM25523KWV, NZM25613KWV, NZM19483KWV, NZM21523KWV, and NZM27613KH represent a commitment to quality, efficiency, and versatility in lawn care tools. With their powerful engines, innovative cutting systems, durable construction, and user-friendly features, these mowers are well-equipped to tackle any mowing challenge, ensuring a beautifully manicured lawn every time.
Top Page Image Contents