Snapper SPLHI53KW important safety instructions Familiarization, Introduction, Nomenclature

Page 6

SECTION 1 - FAMILIARIZATION

RIGHT HAND

TRACTIONSPEED

LEVERCONTROL

LEVER

OPERATOR'S PRESENCE

CONTROL(OPC)

NEUTRAL

LATCH

KEY

SWITCH

		FILL/CHECK CAP
	HYDRAULIC	(Hydraulic Reservoir)
	PUMPS (Not	(Hydraulic Reservoir)
	PUMPS (Not
	Shown)

FUEL SHUT-OFF J

VALVE (Not Shown)

t"

HYDRAULIC DRIVE

MOTOR

(Behind Each Rear

Wheel)

DISCHARGE

DEFLECTOR

MUFFLER

	LEFT HAND
	TRACTION	BLADE CLUTCH
	LEVER	BLADE CLUTCH
	LEVER	CONTROLSWITCH
		CONTROLSWITCH

COVER

CONTROL

FILLER CAP

FUELTANK

STARTER ROPE

AIR FILTER

REARTIRES

DECK HEIGHT

ADJUSTING

CRANK

COVER

RETAINING

KNOBS

CASTER

WHEEL

ASSEMBLY

FRONT

TIRES

DECK

(48"Shown)

FIGURE 1.1

1.1INTRODUCTION

This manual has been prepared for the operator's of the SNAPPER PRO HYDRO WALK BEHIND MOWER. It's

purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating

practices. Read, Understand and Follow the IMPORTANT SAFETY INSTRUCTIONS on Pages 2 thru

4 of this manual and All SAFETY messages on the PRO HYDRO WALK BEHIND MOWER and its attachments

before operating. SNAPPER recommends returning the machine to an authorized SNAPPER dealer annually for inspection and addition of any new devices which might upgrade the safety of the mower.

1.2NOMENCLATURE

It is recommended that all operator's of this equipment

become thoroughly familiar with the controls, components, and operation of this machine before operating. Specific details involving the engine are found in the separate engine owner's manual. Study these manuals before operating and keep both handy for future reference. For the nearest SNAPPER dealer in your area, check the yellow pages under the heading LAWN MOWERS. For engine parts and service, look for the engine manufacturer's dealers under the heading, ENGINES - gasoline.

Image 6

Contents PRO Hydro Walk Behind Mowers MID-SIZE Series Model Number ExplanationMcDonough, Georgia 30253. Phone Important Safety InstructionsPreparation Protection for ChildrenSafe Handling of Gasoline OperationPreparation Do not raise deck with the blades runningMaintenance Contents Familiarization IntroductionNomenclature Safety Messages and Symbols ILATCI , O Read Operators ManualSafety Messages and Symbols Blade and Traction Controls When the Operators Presence Control OPC isEngine Controls Neutral Latch is notWARNINGintended to be used as a parkOperating Instructions PRE-START ChecklistSafety Interlock System Checks 3, Before OperatingStopping Starting and OperatingStart mowing with a slow ground speed Traction Speed Control Forward SpeedReverse Speed Mower OperationMowing and Turning on Hillsides Handle Height AdjustmentMower Operation from Previous On NextFrom previous Shift Lever ARM Dlebar Loosen Bolt ConnectedAdjusting Blade on Cutter Spindle Cutting Height AdjustmentAdjusting Caster Wheels Fixed Deck AFrACHMENTAdjustable Deck Attachments Cutting Height Adjustments forAdjusting Fixed Deck Attachment Side Profile of MachineEngine Troubleshooting Symptom Problem SolutionService Lubrication InformationBREAK-IN Procedure CommentsHours Grease Zerk LocationElectric Clutch Adjustment 2, PUMP/MOTOR Replacement3, Hydraulic Pump Belt Removal Traction Control Neutral Adjustment 4, Hydraulic Pump Belt Installation5, Replacement Parts 3, Hydraulic Pump Belt RemovalAdjustment Traction Control NeutralMower Attachment Service InstallationhandCutter Deck Belt Removal Decks Standard Blade ReplacementSpindle to Spindle Deck Belt Blade Removal and SharpeningMower Spindles Field Serviceable Spindles Bearing ReplacementBattery Service Battery RemovalBattery Installation Battery TestingNEW Battery Preparation IAo%%2,,AIYear Limited Warranty Disclaimer of WarrantySnapper Product Registration Form How Quickly ruin an engine Cost YOU MoneyiCheck OIL Level Before Each START-UP Starting Check List Service Notes PRO Hydro MID-SIZE Walk Behind Mowers Series