Snapper SPLHI53KW Electric Clutch Adjustment, 2, PUMP/MOTOR Replacement

Page 21

SECTION 4 - SERVICE

WARNING

Once blades are disengaged, they should come to a complete stop in 7 seconds or less. If the blades continue to rotate after 7 seconds, the electric clutch must be checked. Replacement of electric clutch may be necessary. Return machine to dealer for replacement. DO NOT CONTINUE to operate mower if blades fail to stop in 7 seconds.

4.1 ELECTRIC CLUTCH ADJUSTMENT

The Pro Hydro Mowers are equipped with an Electric Blade Control. The cutter blades should STOP within 7 seconds

after the BLADE SWITCH is moved to "OFF" position. If blade stopping time exceeds 7 seconds, check the dutch air gap setting as follows:

1.With the Ignition Switch moved to "STOP" and the Blade Switch moved to "OFF", locate the three air gap check "SLOTS" as shown in Figure 4.2.

ADJUST

AIR GAP TO

ADJUSTING NUT

BE .010

TO .012.

 

CLUTCH

FIGURE 4.2

2.Insert a feeler gauge into each of the three slots.

3.The clearance in each slot should be NO MORE than

.010 to .012.

4.If adjustment is required, keep feeler gauge in slot and turn the adjusting nut until the gap is correct.

5.Adjust allthree slots.

4,2 HYDRAULIC SYSTEM ADJUSTMENTS & SERVICE

4,2.1. GENERAL HYDRAULIC SERVICING

1.The Hydraulic Oil and Filter should be changed after the initial 25 hours of use and after every 200 hours of use. Drain both compartments of the hydraulic reservoir completely. Replace filter using genuine Snapper replacement only.

Fill reservoir using 1 gallon of SAE10W-30 oiI. Operate machine for several minutes.

Check oil level. Reservoir is properly filled when level is 1- 1/2" from the top of the filler neck. See Figure 3.1.

NOTE: Always clean the Cap and surrounding area before checking OiI Level or adding Oil. The Hydraulic OiI Tank is

FULL when the Oil is 1-1/2" from the top of the filler neck as shown in Figure 3.1.

2.Before removing parts from the Hydraulic System, check to make sure another part of the machine is not causing

the problem. Look for:

A.Loose Drive Belt.

B.Improperly set or bad Idler Pulley.

C.Loose or lost set screws and/or sheared Keys in Pulleys.

D.Pump Release loose.

E.Oil saturated Drive Belts.

F.Loose Drive Arms on Pumps.

4,2,2, PUMP/MOTOR REPLACEMENT

1.Should it become necessary to replace a Pump or Motor, it is recommended that the affected Pump or Motor be replaced as a set (both Pump and Motor). Generally, when a Pump or Motor is bad, it wilI affect the associated Pump or Motor.

2.Relieve all pressure in the system and disconnect Spark

Plug(s). See Figure 4.3.

3.

TURN PRESSURE RELIEF VALVE ON EACH PUMP

COUNTER-CLOCKWISE TO RELEIVE SYSTEM

PRESSURE.

FIGURE 4,3

4,2,3, HYDRAULIC PUMP BELT REMOVAL

1.STOP ENGINE! Loosen and remove Nut from under the

Spring Tensioner for Hydraulic Belt Idler Tensioner. Remove Spring from Bolt. See Figure 4.4.

HYDRAULIC

PUMP BELT

BOLT

/

SPRING TENSIONER

REMOVE NUT

FIGURE 4.4

21

Image 21
Contents Model Number Explanation PRO Hydro Walk Behind Mowers MID-SIZE SeriesPreparation Important Safety InstructionsMcDonough, Georgia 30253. Phone Protection for ChildrenPreparation OperationSafe Handling of Gasoline Do not raise deck with the blades runningMaintenance Contents Familiarization IntroductionNomenclature Safety Messages and Symbols Read Operators Manual ILATCI , OSafety Messages and Symbols Engine Controls When the Operators Presence Control OPC isBlade and Traction Controls Neutral Latch is notWARNINGintended to be used as a parkSafety Interlock System Checks PRE-START ChecklistOperating Instructions 3, Before OperatingStarting and Operating StoppingReverse Speed Traction Speed Control Forward SpeedStart mowing with a slow ground speed Mower OperationMower Operation from Previous Handle Height AdjustmentMowing and Turning on Hillsides On NextShift Lever ARM Dlebar Loosen Bolt Connected From previousAdjusting Caster Wheels Cutting Height AdjustmentAdjusting Blade on Cutter Spindle Fixed Deck AFrACHMENTAdjusting Fixed Deck Attachment Cutting Height Adjustments forAdjustable Deck Attachments Side Profile of MachineSymptom Problem Solution Engine TroubleshootingLubrication Information ServiceHours Procedure CommentsBREAK-IN Grease Zerk LocationElectric Clutch Adjustment 2, PUMP/MOTOR Replacement3, Hydraulic Pump Belt Removal 5, Replacement Parts 4, Hydraulic Pump Belt InstallationTraction Control Neutral Adjustment 3, Hydraulic Pump Belt RemovalTraction Control Neutral AdjustmentMower Attachment Service InstallationhandCutter Deck Belt Removal Spindle to Spindle Deck Belt Standard Blade ReplacementDecks Blade Removal and SharpeningBearing Replacement Mower Spindles Field Serviceable SpindlesBattery Installation Battery RemovalBattery Service Battery TestingIAo%%2,,AI NEW Battery PreparationDisclaimer of Warranty Year Limited WarrantySnapper Product Registration Form How Cost YOU Moneyi Quickly ruin an engineCheck OIL Level Before Each START-UP Starting Check List Service Notes PRO Hydro MID-SIZE Walk Behind Mowers Series