SECTION | 4 - SERVICE | & LUBRICATION | INFORMATION | ||||||||||
HOURS | PROCEDURE |
|
|
|
|
| COMMENTS |
| |||||
| Check |
| all fasteners | for proper | tightness |
|
|
|
| ||||
| Change |
| Engine | Oil and Filter | at 5 hours | See engine | manual | ||||||
| Change |
| Hydraulic | Oil and Filter at 25 hours | Use SAE |
| |||||||
8 HOURS |
|
|
|
|
|
|
|
|
| Reservoir capacity | 1 Gal. | ||
Check/Change |
| Engine | Oil | Change | oil if extreme dusty conditions | ||||||||
(Daily) | Clean | Air Filter |
|
|
| More often | if needed | ||||||
| Clean | Blower | screen |
| More often | if needed | |||||||
| Remove | Debris from under Belt Cover | More often if needed | ||||||||||
| Sharpen | Cutter | Blades | ......................................................... | Tighten | Cap Screw to 70 - 80 ft. Ibs. | |||||||
| Grease |
| Cutter | Spindle | Bearings | Use Chevron SRI Grease (NLGI2). | |||||||
40 HOURS | Check |
| Hydraulic | Reservoir | Add oil if needed |
| |||||||
Check |
| Tire Pressure |
| Add or adjust as Required | |||||||||
(Weekly) | Check |
| Safety | Interlock | System | Inspect | Switches for ease of Operation | ||||||
| Grease |
| Traction | Control Levers | General | Purpose | Grease | ||||||
| Inspect |
| Traction | Lock for Wear | Replace | if Worn |
| ||||||
| Change |
| Engine | Oil | ................................................................ |
| More often if needed | ||||||
| Replace | Air Filter |
|
| More often | if needed | |||||||
| Grease |
| Caster | Wheel | Bearings | General | Purpose | Grease | |||||
| Grease |
| Caster | Wheel | Pivot | General | Purpose | Grease | |||||
200 HOURS | Grease |
| Idler Arm Pivots | General | Purpose | Grease | |||||||
Fuel Filter |
|
|
|
| Replace with Snapper PIN 7014359 | ||||||||
(Monthly) | Check |
| all Fasteners for Proper tightness | See Torque | Specifications | ||||||||
| Change |
| Engine | Oil Filter | See Engine | Manual | |||||||
| Clean and Adjust Spark Plugs | .............................................. | See Engine | Manual | |||||||||
| Check |
| Belt Tension | ............................................................... |
| See Operator's Manual | |||||||
| Lube Controls | and | Linkages | Use Medium Duty Oil | |||||||||
| Change |
| Hydraulic | Oil and Filter | Use SAE | Oil. | |||||||
|
|
|
|
|
|
|
|
|
| Reservoir capacity | 1 Gal. | ||
GREASE ZERK LOCATION
1 on the Hydro Pump Belt Idler Arm Pivot
1 on each Spindle Housing ITotal of 2 on 36" Deck & 3 on 48", 52", 48", & 61" Decks) 1 on each Idler Arm Pivot (Total of 1 on 36" Deck & 2 on 48", 52", 48", & 61" Decks)
1 on each Caster Support Arm ITotal of 2)
1 on each Caster Wheel (Total of 2)
1 on each Traction Control Lever (Total of 2)
GREASE GREASE
DAILY WEEKLY
X
X
X
X
X
X
MAINTENANCE/REPLACEMENT PARTS
|
|
| MAINTENANCE | PARTS | ||
36 _ | Cutter | Blade | (Requires | Two Blades) | 7029246 | |
48" | Cutter | Blade | (Requires | Three | Blades) | 7029247 |
52" | Cutter | Blade | IRequires | Three | Blades) | 7029246 |
61" | Cutter | Blade | (Requires | Three | Blades) | 7029251 |
36" | Deck | Engine | to Cutting | Deck Belt | 7029255 | |
48" | Deck | En_line to Cuttin_l Deck Belt | 7029262 | |||
48" | Deck Spindle | to Spindle | Belt |
| 7029261 | |
52" | Deck | Engine | to Cutting | Deck Belt | 7029267 | |
52" | Deck Spindle | to Spindle | Belt |
| 7029266 | |
61" | Deck | En_line to Cuttin_l Deck Belt | 7029269 | |||
61" | Deck Spindle | to Spindle | Belt |
| 7029268 | |
| 7006936 | |||||
Parts Manual for | Pro Hydro Series | 3 | ||||
2O