Snapper YZ20484BVE, YZ16424BVE Front or Rear View of Deck Twin Blade Deck, Single Blade Deck

Page 18

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.2.9.MOWER DECK ADJUSTMENT (LEVELNESS) 1. Side-To-Side (42”Decks)

Before making deck leveling adjustments, check the tire pressure. Check tires and add or release air as needed to bring pressure to 12 P.S.I. in front and 12 P.S.I. in rear tires. If tires are properly inflated and mowing is still uneven, adjust side-to-side deck levelness as follows:

a. Place YARD CRUISER on a smooth level surface.

b. Turn engine off and remove key, remove spark plug wire(s) from spark plug(s) and secure wire(s) away from plug(s).

c. Place a piece of angle iron, pipe, or similar object under center of deck at the rear.

d. Remove rear hanger chains and allow center, rear of deck to rest on angle iron.

e. Measure the distance from blade tips to floor. If the measurement is within 1/8” from side-to-side, the deck levelness is satisfactory. If the difference from side-to-side is greater than 1/8”, continue to the Step “f” for adjustment. See Figure 4.6.

FRONT OR REAR VIEW OF DECK

 

TWIN BLADE DECK

 

X

 

X - 1/8”

 

 

SIDE

 

SIDE

 

ANGLE

 

 

IRON

 

X

SINGLE BLADE DECK

X - 1/8”

FIGURE 4.6

SIDE

 

SIDE

f. Loosen the shoulder bolt that retains the eccentric.

g. Turn eccentric “UP” or “DOWN” as required until blade tips are within 1/8” of the same distance from the floor. See Figure 4.7.

h.Tighten shoulder bolt loosened in Step “f”.

i.Readjust rear hanger chain pivots to align with holes in support brackets.

j.Reconnect hanger chains, remove angle iron, pipe, etc. and recheck side to side level. Adjust either chain as needed to result in blade tips being within 1/8” of the same distance from the floor.

k.Proceed to check front to rear deck pitch.

42” DECK SHOWN

UP

LOOSEN SHOULDER BOLT

FRONT DOWN LIFT ARM

ECCENTRIC

FIGURE 4.7

(Continued On Next Page)

ANGLE IRON

19

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Yard Cruiser Important Safety Instructions Operation Table of Contents Introduction NomenclatureOperating Instructions PRE-START Check ListStarting & Operation Engine Electric Start Wheel Drive Mower BladeStopping 2.3.1. Engine Parking BrakeCutting Height Adjustment Check Mower Blade Service After First 5 HoursChange Engine OIL Twin & Triple Blade DeckService Every 25 Operating Hours Check Mower Drive Belt 1. Footrest RemovalService Every 25 Operating Hours 3.3.1. Engine Mower ComponentsYard Cruiser Lubrication Front Wheel BearingsService Annually Storage OUT of SeasonMower Drive Belt Adjustment Belt ReplacementBelt Removal Blade Brake Hairpin Lift ARM Front or Rear View of Deck Twin Blade Deck Single Blade DeckDeck Shown Wheel Brake Adjustment Mower Blade Replacement 4.3.1. Blade Wear Limits Blade ReplacementBlade Sharpening Battery Battery Removal Battery ServiceBattery Storage Battery Condition Chart Battery TestingTroubleshooting Problem Probable Cause Corrective ActionMAINTENANCE/REPLACEMENT Parts Loss Of TractionService Performed Each USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Yard Cruiser Hydro Drive Series

YZ16424BVE, YZ20484BVE, YZ20484BVE, YZ16424BVE specifications

The Snapper YZ16424BVE and YZ20484BVE lawn mowers represent a notable advancement in residential and commercial landscaping technology. Engineered for efficiency, both models showcase cutting-edge features that enhance performance while ensuring user comfort.

The YZ16424BVE boasts a robust 24-horsepower engine, providing ample power for tackling various lawn conditions. This model is equipped with a 42-inch cutting deck, allowing for quick and efficient mowing of medium to large yards. Its dual-blade system offers superior mulch and bagging capabilities, giving users the flexibility to choose how they want to care for their lawns. The YZ16424BVE also features adjustable cutting heights, giving users precise control over their lawn's appearance.

On the other hand, the YZ20484BVE takes it a step further with a formidable 48-inch cutting deck and a 24-horsepower engine. This model is tailored for larger properties, significantly reducing mowing time without compromising on quality. The YZ20484BVE incorporates Snapper's innovative ReadyStart technology, which eliminates the need for priming the engine. This ensures hassle-free startups every time, making it an ideal choice for those who prefer a quick and straightforward mowing experience.

Both models are designed with user comfort in mind. Featuring ergonomic, adjustable seating, they provide a comfortable ride even during extended mowing sessions. The smooth maneuverability of the zero-turn steering allows for precise control, enabling users to navigate around obstacles effortlessly. This feature reduces the effort required to achieve a perfectly manicured lawn.

Durability is also a significant highlight of both the YZ16424BVE and YZ20484BVE. Built with high-quality materials, these mowers are designed to withstand the rigors of regular use. Their reinforced frames and heavy-duty wheels ensure stability and reliability across various terrains.

In summary, Snapper's YZ16424BVE and YZ20484BVE models are powerful, efficient, and user-friendly lawn mowers that cater to different yard sizes and needs. With advanced technologies, customizable features, and robust construction, they stand out as exceptional choices for anyone looking to maintain a beautiful lawn with ease and precision. Whether you're managing a small garden or a sprawling estate, these mowers deliver the performance needed to achieve landscaping excellence.
Top Page Image Contents