Snapper YZ20484BVE, YZ16424BVE, YZ16424BVE, YZ20484BVE Service Annually, Storage OUT of Season

Page 14

Section 3 – MAINTENANCE

3.4 SERVICE - ANNUALLY

Perform all maintenance as described in the maintenance schedule.

3.4.1. Engine

Service engine according to engine owner’s manual.

3.4.2. Air Filter

Refer to engine owner’s manual for service instructions.

3.4.3. Oil Filter

Refer to engine owner’s manual for service instructions.

3.4.4. Engine Oil

Refer to engine owner’s manual for service instructions.

3.4.5. Transaxle

IMPORTANT: DO NOT try to open reservoir cap at any time. The transaxle is maintenance free. The transaxle does not require any fluid or any service. If there is any problem: leakage, malfunction or etc. return the Yard Cruiser immediately to the nearest authorized Snapper dealer for service.

3.4.6. Fuel Filter

Service fuel filter as instructed below. Turn key to “OFF” position. Engine MUST be stopped and MUST be cold before removing filter. Perform filter change when fuel tank and fuel line is empty.

1.Remove hose clamps from fuel filter.

2.Remove fuel lines from filter. Discard filter.

3.Install new fuel filter. Reinstall hose clamps. See Figure 3.8.

NEW FUEL

FILTER

HOSE

CLAMPS

FIGURE 3.8

3.5 STORAGE (OUT OF SEASON)

If desired, the YARD CRUISER can be stored on the rear bumper. Perform the following procedures to insure the YARD CRUISER will operate properly when taken out of storage.

3.5.1.Thoroughly clean the YARD CRUISER by removing all grass clippings and debris.

3.5.2.Perform maintenance and lubrication as described in the previous sections.

3.5.3.Drain fuel from fuel tank.

3.5.4.Start engine and allow it to run until engine runs out of fuel. This allows the carburetor and fuel system to remain clean during storage.

3.5.5.Remove battery. Refer to Section

“BATTERY REMOVAL AND STORAGE”.

3.5.6.Close vent on fuel filler cap. Remove key.

3.5.7.Carefully stand YARD CRUISER on rear bumper in desired location for storage.

15

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Yard Cruiser Important Safety Instructions Operation Table of Contents Introduction NomenclatureOperating Instructions PRE-START Check ListStarting & Operation Engine Electric Start Wheel Drive Mower BladeStopping 2.3.1. Engine Parking BrakeCutting Height Adjustment Check Mower Blade Service After First 5 HoursChange Engine OIL Twin & Triple Blade DeckService Every 25 Operating Hours Check Mower Drive Belt 1. Footrest RemovalService Every 25 Operating Hours 3.3.1. Engine Mower ComponentsYard Cruiser Lubrication Front Wheel BearingsService Annually Storage OUT of SeasonBelt Removal Mower Drive Belt AdjustmentBelt Replacement Blade Brake Hairpin Lift ARM Deck Shown Front or Rear View of Deck Twin Blade DeckSingle Blade Deck Wheel Brake Adjustment Blade Sharpening Mower Blade Replacement 4.3.1. Blade Wear LimitsBlade Replacement Battery Storage Battery Battery RemovalBattery Service Battery Condition Chart Battery TestingTroubleshooting Problem Probable Cause Corrective ActionMAINTENANCE/REPLACEMENT Parts Loss Of TractionService Performed Each USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Yard Cruiser Hydro Drive Series

YZ16424BVE, YZ20484BVE, YZ20484BVE, YZ16424BVE specifications

The Snapper YZ16424BVE and YZ20484BVE lawn mowers represent a notable advancement in residential and commercial landscaping technology. Engineered for efficiency, both models showcase cutting-edge features that enhance performance while ensuring user comfort.

The YZ16424BVE boasts a robust 24-horsepower engine, providing ample power for tackling various lawn conditions. This model is equipped with a 42-inch cutting deck, allowing for quick and efficient mowing of medium to large yards. Its dual-blade system offers superior mulch and bagging capabilities, giving users the flexibility to choose how they want to care for their lawns. The YZ16424BVE also features adjustable cutting heights, giving users precise control over their lawn's appearance.

On the other hand, the YZ20484BVE takes it a step further with a formidable 48-inch cutting deck and a 24-horsepower engine. This model is tailored for larger properties, significantly reducing mowing time without compromising on quality. The YZ20484BVE incorporates Snapper's innovative ReadyStart technology, which eliminates the need for priming the engine. This ensures hassle-free startups every time, making it an ideal choice for those who prefer a quick and straightforward mowing experience.

Both models are designed with user comfort in mind. Featuring ergonomic, adjustable seating, they provide a comfortable ride even during extended mowing sessions. The smooth maneuverability of the zero-turn steering allows for precise control, enabling users to navigate around obstacles effortlessly. This feature reduces the effort required to achieve a perfectly manicured lawn.

Durability is also a significant highlight of both the YZ16424BVE and YZ20484BVE. Built with high-quality materials, these mowers are designed to withstand the rigors of regular use. Their reinforced frames and heavy-duty wheels ensure stability and reliability across various terrains.

In summary, Snapper's YZ16424BVE and YZ20484BVE models are powerful, efficient, and user-friendly lawn mowers that cater to different yard sizes and needs. With advanced technologies, customizable features, and robust construction, they stand out as exceptional choices for anyone looking to maintain a beautiful lawn with ease and precision. Whether you're managing a small garden or a sprawling estate, these mowers deliver the performance needed to achieve landscaping excellence.
Top Page Image Contents