Snapper YZ16424BVE, YZ20484BVE Battery Battery Removal, Battery Service, Battery Storage

Page 21

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. Never attempt to service or charge the battery while it is installed on the YARD CRUISER. Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal, which could cause sparks. Cables must be connected to battery terminals in the proper position as shown. If battery is removed, DO NOT operate engine without insulating Positive + battery cable terminal with electrical tape, or sparking from the battery cables can result.

4.4BATTERY

4.4.1. BATTERY REMOVAL

1.Tilt seat up to gain access to battery.

2.Observe and note cable positions on battery. See Figure 4.14.

3.Disconnect cables from battery terminals, disconnecting BLACK (Negative) cable first. Disconnect RED (Positive) battery cable. Slide battery from battery cradle.

4.Retain mounting bolts and nuts for future use.

4.4.2.BATTERY INSTALLATION 1. Slide battery into battery cradle.

2. Connect cables to battery terminals. Connect RED (Positive) cable first. Connect BLACK (Negative) cable. See Figure 4.14.

3. Place the positive (+) terminal insulator over positive terminal and cable. See Figure 4.15.

BLACK

NEGATIVE (-)

CABLE

RED

POSITIVE (+)

CABLE

FIGURE 4.14

WARNING

The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid. Wear eye protection. Wash affected areas immediately after having eye or skin contact with electrolyte (acid). Battery acid is corrosive. Rinse empty acid containers with water and mutilate before discarding. If acid is spilled on battery, bench, or clothing, etc., Flush with clear water and neutralize with baking soda. DO NOT attempt to charge battery while installed on the YARD CRUISER. DO NOT use “BOOST” chargers on the battery.

4.4.3. BATTERY SERVICE

1.Remove battery. See Section on Battery Removal

2.Place battery in a well ventilated area on a level surface.

3.Using distilled water, refill cells as required to cover cell plates. Fluid level in battery can be seen through the cell case.

4.With cell caps removed, connect battery charger to battery terminals. Red to positive (+) terminal and black to negative (-) terminal.

5.Slow charge battery at 1 amp for 10 hours.

6.If battery will not accept charge or is partially charged after 10 hours of charging at 1 amp, replace with new battery, Part Number 6-0753.

4.4.4. BATTERY STORAGE

If YARD CRUISER is to be stored out of season on its rear bumper, it is recommended the battery be removed, charged and stored.

1.Remove battery. (Refer to Section ”BATTERY REMOVAL”).

2.Perform battery service.

3.Bring battery to full charge, if required.

4.Store battery in an area away from the YARD CRUISER on a wood surface. DO NOT STORE BATTERY ON A CONCRETE SURFACE.

4.4.5.NEW BATTERY PREPARATION 1. Remove battery from carton.

2. Place battery in a well ventilated area on a level non-concrete surface.

3. Remove battery cell caps. Fill cells as required with electrolyte (purchased separately) to proper level. Fill to 3/16” above cell plates. Filling battery with electrolyte will bring the battery to 80% charged state.

4. With cell caps removed, connect battery charger to battery terminals; RED to positive (+) and BLACK to negative (-) terminal.

22

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Yard Cruiser Important Safety Instructions Operation Table of Contents Nomenclature IntroductionPRE-START Check List Operating InstructionsStarting & Operation Engine Electric Start Stopping 2.3.1. Engine Mower BladeWheel Drive Parking BrakeCutting Height Adjustment Change Engine OIL Service After First 5 HoursCheck Mower Blade Twin & Triple Blade DeckCheck Mower Drive Belt 1. Footrest Removal Service Every 25 Operating HoursMower Components Service Every 25 Operating Hours 3.3.1. EngineFront Wheel Bearings Yard Cruiser LubricationStorage OUT of Season Service AnnuallyMower Drive Belt Adjustment Belt ReplacementBelt Removal Blade Brake Hairpin Lift ARM Front or Rear View of Deck Twin Blade Deck Single Blade DeckDeck Shown Wheel Brake Adjustment Mower Blade Replacement 4.3.1. Blade Wear Limits Blade ReplacementBlade Sharpening Battery Battery Removal Battery ServiceBattery Storage Battery Testing Battery Condition ChartProblem Probable Cause Corrective Action TroubleshootingLoss Of Traction MAINTENANCE/REPLACEMENT PartsUSE HRS Season Service Performed EachDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Yard Cruiser Hydro Drive Series

YZ16424BVE, YZ20484BVE, YZ20484BVE, YZ16424BVE specifications

The Snapper YZ16424BVE and YZ20484BVE lawn mowers represent a notable advancement in residential and commercial landscaping technology. Engineered for efficiency, both models showcase cutting-edge features that enhance performance while ensuring user comfort.

The YZ16424BVE boasts a robust 24-horsepower engine, providing ample power for tackling various lawn conditions. This model is equipped with a 42-inch cutting deck, allowing for quick and efficient mowing of medium to large yards. Its dual-blade system offers superior mulch and bagging capabilities, giving users the flexibility to choose how they want to care for their lawns. The YZ16424BVE also features adjustable cutting heights, giving users precise control over their lawn's appearance.

On the other hand, the YZ20484BVE takes it a step further with a formidable 48-inch cutting deck and a 24-horsepower engine. This model is tailored for larger properties, significantly reducing mowing time without compromising on quality. The YZ20484BVE incorporates Snapper's innovative ReadyStart technology, which eliminates the need for priming the engine. This ensures hassle-free startups every time, making it an ideal choice for those who prefer a quick and straightforward mowing experience.

Both models are designed with user comfort in mind. Featuring ergonomic, adjustable seating, they provide a comfortable ride even during extended mowing sessions. The smooth maneuverability of the zero-turn steering allows for precise control, enabling users to navigate around obstacles effortlessly. This feature reduces the effort required to achieve a perfectly manicured lawn.

Durability is also a significant highlight of both the YZ16424BVE and YZ20484BVE. Built with high-quality materials, these mowers are designed to withstand the rigors of regular use. Their reinforced frames and heavy-duty wheels ensure stability and reliability across various terrains.

In summary, Snapper's YZ16424BVE and YZ20484BVE models are powerful, efficient, and user-friendly lawn mowers that cater to different yard sizes and needs. With advanced technologies, customizable features, and robust construction, they stand out as exceptional choices for anyone looking to maintain a beautiful lawn with ease and precision. Whether you're managing a small garden or a sprawling estate, these mowers deliver the performance needed to achieve landscaping excellence.
Top Page Image Contents