Snapper YZ20484BVE, YZ16424BVE Mower Blade Replacement 4.3.1. Blade Wear Limits, Blade Sharpening

Page 20

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

4.3MOWER BLADE REPLACEMENT 4.3.1. BLADE WEAR LIMITS

1.Inspect blade frequently for signs of excessive wear or damage. See Figure 4.11.

NEW BLADE

WEAR LIMIT (NOTCH STARTS)

DANGEROUS CONDITION!

DO NOT USE ON MOWER!

REPLACE WITH NEW BLADE.

FIGURE 4.11

4.3.2. BLADE SHARPENING

1.Make sure fuel cap is on tight. Start engine and allow it to run until engine runs out of fuel. Close vent on fuel filler cap. See Figure 2.3.

2.Remove key from ignition switch.

3.Remove spark plug wire(s) and secure away from spark plug(s).

4.Carefully stand YARD CRUISER on rear bumper.

5.Remove blade(s). See Figure 4.12.

6.Inspect condition of blade. See Figure 4.11.

7.If blade is in good condition, sharpen at 22 to 28 degrees. DO NOT sharpen beyond existing cutting edge. See Figure 4.13.

8.Check blade balance after sharpening. If necessary, correct blade balance by grinding the heavy end of blade.

9.Reinstall blade. See Figure 4.12. Torque blade mounting bolts to recommended range of:

42” Deck - 30 to 40 ft. lbs. 48” Deck - 80 to 90 ft. lbs.

48” DECK

42” DECK

FIGURE 4.12

DO NOT SHARPEN

BEYOND ORIGINAL 22º TO 28º

CUTTING EDGE

BLADE TIP

ORIGINAL CUTTING EDGE

FIGURE 4.13

WARNING

DO NOT use a cutting blade that shows signs of excessive wear or damage. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

4.3.3. BLADE REPLACEMENT

1.Remove blade(s). See Figure 4.12. Replace blade(s) if it shows signs of excessive wear or damage.

NOTE: FOR ALL CUTTING BLADE REPLACEMENT PARTS IDENTIFICATION NUMBERS SEE PAGE 24.

21

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Yard Cruiser Important Safety Instructions Operation Table of Contents Introduction NomenclatureOperating Instructions PRE-START Check ListStarting & Operation Engine Electric Start Mower Blade Stopping 2.3.1. EngineWheel Drive Parking BrakeCutting Height Adjustment Service After First 5 Hours Change Engine OILCheck Mower Blade Twin & Triple Blade DeckService Every 25 Operating Hours Check Mower Drive Belt 1. Footrest RemovalService Every 25 Operating Hours 3.3.1. Engine Mower ComponentsYard Cruiser Lubrication Front Wheel BearingsService Annually Storage OUT of SeasonBelt Removal Mower Drive Belt AdjustmentBelt Replacement Blade Brake Hairpin Lift ARM Deck Shown Front or Rear View of Deck Twin Blade DeckSingle Blade Deck Wheel Brake Adjustment Blade Sharpening Mower Blade Replacement 4.3.1. Blade Wear LimitsBlade Replacement Battery Storage Battery Battery RemovalBattery Service Battery Condition Chart Battery TestingTroubleshooting Problem Probable Cause Corrective ActionMAINTENANCE/REPLACEMENT Parts Loss Of TractionService Performed Each USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Yard Cruiser Hydro Drive Series

YZ16424BVE, YZ20484BVE, YZ20484BVE, YZ16424BVE specifications

The Snapper YZ16424BVE and YZ20484BVE lawn mowers represent a notable advancement in residential and commercial landscaping technology. Engineered for efficiency, both models showcase cutting-edge features that enhance performance while ensuring user comfort.

The YZ16424BVE boasts a robust 24-horsepower engine, providing ample power for tackling various lawn conditions. This model is equipped with a 42-inch cutting deck, allowing for quick and efficient mowing of medium to large yards. Its dual-blade system offers superior mulch and bagging capabilities, giving users the flexibility to choose how they want to care for their lawns. The YZ16424BVE also features adjustable cutting heights, giving users precise control over their lawn's appearance.

On the other hand, the YZ20484BVE takes it a step further with a formidable 48-inch cutting deck and a 24-horsepower engine. This model is tailored for larger properties, significantly reducing mowing time without compromising on quality. The YZ20484BVE incorporates Snapper's innovative ReadyStart technology, which eliminates the need for priming the engine. This ensures hassle-free startups every time, making it an ideal choice for those who prefer a quick and straightforward mowing experience.

Both models are designed with user comfort in mind. Featuring ergonomic, adjustable seating, they provide a comfortable ride even during extended mowing sessions. The smooth maneuverability of the zero-turn steering allows for precise control, enabling users to navigate around obstacles effortlessly. This feature reduces the effort required to achieve a perfectly manicured lawn.

Durability is also a significant highlight of both the YZ16424BVE and YZ20484BVE. Built with high-quality materials, these mowers are designed to withstand the rigors of regular use. Their reinforced frames and heavy-duty wheels ensure stability and reliability across various terrains.

In summary, Snapper's YZ16424BVE and YZ20484BVE models are powerful, efficient, and user-friendly lawn mowers that cater to different yard sizes and needs. With advanced technologies, customizable features, and robust construction, they stand out as exceptional choices for anyone looking to maintain a beautiful lawn with ease and precision. Whether you're managing a small garden or a sprawling estate, these mowers deliver the performance needed to achieve landscaping excellence.
Top Page Image Contents