Nozzle Maintenance

Snapper 2400 PSI Pressure Washer

To remove contaminants from the pump, follow these steps:

•Set up the pressure washer as described in “Preparing Pressure Washer For Use”. Connect the water supply and turn water on.

•Remove the nozzle extension from the spray gun.

•Start the engine according to instructions in “How To Use Your Pressure Washer”.

•Squeeze the trigger on the spray gun and hold.

•When the water supply is steady and constant, engage the safety latch and refasten the nozzle extension.

Check In-Line Filter

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it with clean water before stopping the engine.

•Place the detergent siphoning tube in a bucket full of clean water.

•Slide the adjustable nozzle forward to the low pressure position. Flush for 1-2 minutes.

•Shut off the engine.

IMPORTANT: Simply shutting OFF engine will not release pressure in the system. When the engine has

shut down, squeeze the trigger on the spray gun to relieve the pressure in the hose.

Refer to Figure 13 and service the in-line filter if it becomes clogged, as follows:

Figure 13 — Clean In-Line Filter

Filter Screen

Nozzle Extension

O-ring

1.Detach spray gun and nozzle extension from high pressure hose. Detach nozzle extension from spray gun and remove o-ring and screen from nozzle extension. Flush the screen, spray gun, and adjustable nozzle extension with clean water to clear debris.

2.If the screen is damaged, the o-ring kit contains a replacement in-line filter screen and an o-ring. If undamaged, reuse screen.

3.Place the in-line filter screen into the threaded end of the nozzle extension. Direction does not matter. Push the screen in with the eraser end of a pencil until it rests flat at the bottom of the opening.Take care to not bend the screen.

4.Place the o-ring into the recess. Push the o-ring snugly against the in-line filter screen.

5.Assemble the nozzle extension to the spray gun, as described earlier in this manual.

A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure.The principal cause of excessive pump pressure is a nozzle clogged or restricted with foreign materials, such as dirt, etc.To correct the problem, immediately clean the nozzle using the tools included with your pressure washer and follow these instructions:

1.Shut off the engine and turn off the water supply.

2.Detach the nozzle extension from the spray gun.Twist the nozzle clockwise to the stream position. Using the supplied 2mm (5/64) allen wrench, remove the nozzle from the end of the nozzle extension (Figure 14).

Figure 14 — Removing and Cleaning Nozzle

Nozzle

3.Remove the in-line filter from the other end of the nozzle extension.

4.Use the wire included in the kit (or a small paper clip) to free any foreign material clogging or restricting the nozzle (Figure 14).

1660-0 specifications

Snapper 1660-0 is a versatile and robust lawn mower designed for homeowners who seek efficiency and performance in their lawn care. Equipped with a powerful engine and advanced cutting technology, this mower stands out in the competitive market of residential lawn equipment.

One of the main features of the Snapper 1660-0 is its reliable 66-cc OHV engine. This engine delivers sufficient power to handle various types of grass and terrain, ensuring a clean and even cut. The mower's design focuses on user-friendly operation, allowing both seasoned gardeners and newcomers alike to achieve professional results with ease.

The cutting deck of the Snapper 1660-0 measures 21 inches, providing a suitable width for maneuvering around tight spaces while still allowing for efficient cutting of larger areas. The mower utilizes a rear-wheel drive system, which enhances traction and control, particularly on sloped or uneven landscapes. This feature is especially beneficial for homeowners with diverse lawn topographies.

One of the standout characteristics of the Snapper 1660-0 is its adjustable cutting height, which ranges from 1.25 to 4 inches. This adaptability allows users to customize the mowing experience based on their lawn’s specific needs, promoting healthier grass growth by enabling the user to choose the optimal height for their turf type.

In addition to these features, Snapper has integrated their renowned Hi-Vacuum cutting technology into the design of the 1660-0. This technology ensures that grass clippings are effectively lifted and cut, resulting in a superior finish and reduced need for raking or bagging afterward.

For ease of maintenance, the Snapper 1660-0 also includes a convenient washout port, allowing users to clean the underside of the mower deck easily and keep it in top condition. Furthermore, its compact design makes storage straightforward, fitting easily into shed or garage spaces.

Overall, the Snapper 1660-0 offers a combination of power, versatility, and user-friendliness, making it an excellent choice for homeowners looking to maintain their lawns efficiently. With its innovative features and strong performance, this mower is built to cater to the diverse needs of lawn care enthusiasts.