Snapper 1660-0 owner manual Checklist Before Starting Engine, HOW to USE Your Pressure Washer

Page 7

Snapper 2400 PSI Pressure Washer

CHECKLIST BEFORE STARTING ENGINE

Attach the adjustable nozzle extension to the spray gun (Figure 6).Tighten by hand.

Figure 6 — Connect Nozzle Extension to Spray Gun

Review the unit’s assembly to ensure you have performed all of the following.

Check that oil has been added to the proper level in the engine crankcase.

Add the proper gasoline to fuel tank.

Check for properly tightened hose connections (high pressure and water supply) and that there are no kinks, cuts, or damage to the high pressure hose.

Provide a proper water supply at an adequate flow.

Be sure to read "Safety Rules" and "How To Use Your Pressure Washer" before using the pressure washer.

HOW TO USE YOUR PRESSURE WASHER

If you have any problems operating your pressure washer, please contact the local Snapper service center.

How to Start Your Pressure Washer

To start your pressure washer for the first time, follow these instructions step-by-step.This starting information also applies if you have let the pressure washer sit idle for at least a day.

Place the pressure washer in an area close enough to an outside water source capable of supplying water at a flow rate greater than 2.8 gallons per minute.

Check that the high pressure hose is tightly connected to the spray gun and to the pump. See “Preparing Pressure Washer for Use” for illustrations.

Make sure unit is in a level position.

Connect the garden hose to the water inlet on the pressure washer pump. Turn ON the water.

CAUTION! Do Not run the pump without the water supply connected and turned on.You must follow this caution or the pump will be damaged.

Squeeze the trigger on the spray gun until you have a steady stream of water.This purges the pump of air and impurities.

Position the nozzle in the low pressure mode (see “How to Use the Adjustable Nozzle”) and squeeze the trigger on the spray gun to relieve the air pressure caused by turning ON the water.Water will flow out of the spray gun in a thin stream. Continue to hold trigger until there is a steady stream of water and no air remains in the system.This will make it easier to pull start the engine. Release the trigger.

Engage the safety latch to the spray gun trigger (Figure 7).

Figure 7 — Spray Gun with Safety Latch Engaged

Safety Latch

Rotate the choke knob to the “Choke” position (Figure 8).

Figure 8 — Choke Knob

NOTE: For a warm engine, be sure the choke knob is in the “Run” position.

Move the throttle lever to “Fast” position, shown on unit as a rabbit (Figure 9).

7

Image 7
Contents 2400PSI Contact the Local Snapper Service CenterSafety Rules Table of ContentsEquipment Description High pressure spray may damage fragile items including glass Know Your Pressure Washer Add Engine Oil Carton ContentsRemove Pressure Washer from Carton Washer for USETypical Fuel Expansion Space Connect Hose and Water Supply to PumpHOW to USE Your Pressure Washer Checklist Before Starting EngineHow to Start Your Pressure Washer How to Use the Adjustable Nozzle How to Stop Your Pressure WasherAutomatic Cool Down System How to Use the Turbo NozzleApplying Detergent with the Adjustable Nozzle Pressure Washer RinsingGeneral Maintenance Recommendations SpecificationsPressure Washer Maintenance Nozzle Maintenance Check In-Line Filter Cleaning Detergent Siphoning TubeTo remove contaminants from the pump, follow these steps Storing the Engine Engine MaintenanceRing Maintenance Preparing the Unit for StorageSnapper 2400 PSI Pressure Washer Troubleshooting Snapper 2400 PSI Pressure Washer Exploded View Main Unit Qty Description Parts List Main UnitExploded View Pump Parts List Pump Generac Portable Products, LLC Jefferson,Wisconsin U.S.A Snapper Owner Warranty Policy Effective October 1

1660-0 specifications

Snapper 1660-0 is a versatile and robust lawn mower designed for homeowners who seek efficiency and performance in their lawn care. Equipped with a powerful engine and advanced cutting technology, this mower stands out in the competitive market of residential lawn equipment.

One of the main features of the Snapper 1660-0 is its reliable 66-cc OHV engine. This engine delivers sufficient power to handle various types of grass and terrain, ensuring a clean and even cut. The mower's design focuses on user-friendly operation, allowing both seasoned gardeners and newcomers alike to achieve professional results with ease.

The cutting deck of the Snapper 1660-0 measures 21 inches, providing a suitable width for maneuvering around tight spaces while still allowing for efficient cutting of larger areas. The mower utilizes a rear-wheel drive system, which enhances traction and control, particularly on sloped or uneven landscapes. This feature is especially beneficial for homeowners with diverse lawn topographies.

One of the standout characteristics of the Snapper 1660-0 is its adjustable cutting height, which ranges from 1.25 to 4 inches. This adaptability allows users to customize the mowing experience based on their lawn’s specific needs, promoting healthier grass growth by enabling the user to choose the optimal height for their turf type.

In addition to these features, Snapper has integrated their renowned Hi-Vacuum cutting technology into the design of the 1660-0. This technology ensures that grass clippings are effectively lifted and cut, resulting in a superior finish and reduced need for raking or bagging afterward.

For ease of maintenance, the Snapper 1660-0 also includes a convenient washout port, allowing users to clean the underside of the mower deck easily and keep it in top condition. Furthermore, its compact design makes storage straightforward, fitting easily into shed or garage spaces.

Overall, the Snapper 1660-0 offers a combination of power, versatility, and user-friendliness, making it an excellent choice for homeowners looking to maintain their lawns efficiently. With its innovative features and strong performance, this mower is built to cater to the diverse needs of lawn care enthusiasts.