Snapper 020231 Engine Maintenance, Nozzle Maintenance, Ring Maintenance, Pump Maintenance

Page 14

3000 PSI Pressure Washer

1.Detach spray gun and nozzle extension from high pressure hose. Detach nozzle extension from spray gun and remove o-ring and screen from nozzle extension. Flush screen, spray gun, and nozzle extension with clean water to clear debris.

2.Place in-line filter screen into threaded end of nozzle extension. Direction does not matter. Push screen in with eraser end of pencil until it rests flat at bottom of opening.Take care to not bend screen.

3.Place o-ring into recess. Push o-ring snugly against in-line filter screen.

4.Assemble nozzle extension to spray gun, as described earlier in this manual.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure.The principal cause of excessive pump pressure is a spray tip clogged or restricted with foreign materials, such as dirt, etc.To correct the problem, immediately clean the spray tip following these instructions:

1.Shut off engine and turn off water supply.

2.Remove spray tip from end of nozzle extension.

6.Reinstall spray tip and in-line filter into nozzle extension.

7.Reconnect nozzle extension to spray gun.

8.Reconnect water supply, turn on water, and start engine.

9.Test pressure washer by operating with each Quick Connect spray tips.

O–Ring Maintenance

Purchase an O–Ring/Maintenance Kit, part number 191922GS by contacting the nearest authorized service center. It is not included with the pressure washer.This kit includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided in the kit to service your unit’s o-rings.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.

•NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.

3.Remove in-line filter from other end of nozzle extension.

4.Use a small paper clip to free any foreign material clogging or restricting spray tip (Figure 20).

Figure 20 — Nozzle Maintenance

Use wire here

to remove

debris.

5.Using a garden hose, remove additional debris by back flushing water through nozzle extension (Figure 21). Back flush between 30 to 60 seconds.

Figure 21 — Backflushing the Nozzle Extension

Pump Maintenance

This model does not require any pump maintenance.The pump is pre-lubricated and sealed, requiring no additional lubrication for the life of the pump.

ENGINE MAINTENANCE

See the engine owner’s manual for instructions on how to properly maintain the engine.

CAUTION

Avoid prolonged or repeated skin contact with used motor oil.

•Used motor oil has been shown to cause skin cancer in certain laboratory animals.

•Thoroughly wash exposed areas with soap and water.

KEEP OUT OF REACH OF CHILDREN. DON'T POLLUTE. CONSERVE RESOURCES. RETURN USED OIL TO COLLECTION CENTERS.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents PSI Pressure Washer Equipment Description Table of ContentsSafety Rules When Adding Fuel Operate pressure washer only outdoorsHigh pressure spray may damage fragile items including glass Recoil Starter Know Your Pressure WasherChoke Lever Nozzle Extension withAttach Handle and Accessory Tray AssemblyCarton Contents Preparing Pressure Washer for USEAdd Engine Oil and Fuel Handle Align Holes SupportsInspect inlet Checklist Before Starting EngineConnect Hose and Water Supply to Pump Screen, doPressure Washer Location HOW to USE Your Pressure WasherHow to Start Pressure Washer Pressure Washer ClearanceHow to Stop Your Pressure Washer How to Use Accessory TrayLow Pressure How to Use Spray TipsCleaning and Applying Chemical High PressureAutomatic Cool Down System Cleaning Detergent Siphoning TubePressure Washer Rinsing Thermal ReliefPressure Washer Maintenance SpecificationsGeneral Maintenance Recommendations Ring Maintenance Engine MaintenanceNozzle Maintenance Pump MaintenanceStoring the Engine Always wear eye protection when using PumpSaverPreparing the Unit for Storage Protecting the PumpPSI Pressure Washer PSI Pressure Washer Troubleshooting Problem Cause CorrectionEquipment Consumer Use Commercial Use Snapper Owner Warranty Policy Effective August 1About your equipment warranty Portable Generator Years 2nd year parts onlyReglas DE Seguridad Conserve Estas Instrucciones Tabla DE ContenidosDescripción DEL Equipo AdvertenciaCuando Añada Combustible Precaución Etiqueta de Datos Bomba equipado con Conozca SU Maquina Lavadora DE PresionFiltro de Aire Perilla del Cebador Usada para arranque de motores fríosRemueva el Lavador a Presión del Empaque MontajePreparando EL Lavador a Presión Para SU USO Contenido de la CajaColoque la lavadora a presión sobre una superficie nivelada Agregar Aceite al Motor y GasolinaManubrio Alinear Orificios Soportes del Deposite la gasolina adecuada en el tanque del combustible Conecte la Manguera y el Suministro de Agua a la BombaLista de Revision Previa al Arranque del Motor Proporcione el suministro de agua adecuadoUbicación del Lavadora a Presión Cómo Usar SU Lavadora a PresiónPeligro Cómo Darle Arranque a su Lavadora a PresiónCómo Detener su Máquina Lavadora a Presión Figura 35 Control de la Válvula de AdmisiónLa Presión Baja Utilización de la Charola de AccesoriosCómo Usar las Puntas de Rocío La Presión AltaLimpieza y Aplicación del Químico Enjuage de la Máquina Lavadora a PresiónLimpiando el Tubo Sistema de Enfriamiento Automático Alivio TérmicoMantenimiento DE LA Maquina Lavadora a Presion EspecificacionesRecomendaciones Generales Mantenimiento de los Anillos O Mantenimiento DEL MotorMantenimiento de la Boquilla Mantenimiento de la BombaProteger la Bomba Preparando LA Unidad Para SU AlmacenamientoAlmacenando EL Motor Reparacion DE Averias Generador Portátil Efectiva desde el 1 ro de AgostoEquipo Para Uso Del Consumidor Para Uso Comercial Año

020231 specifications

Snapper 020231 is a remarkable addition to the world of outdoor power equipment, specifically designed for homeowners and landscaping professionals looking for efficiency and reliability in their yard maintenance tasks. As part of Snapper’s renowned line of lawn care products, the 020231 model stands out due to its innovative features and advanced technologies that elevate user experience.

One of the most notable features of the Snapper 020231 is its powerful 190cc engine. This high-performance engine ensures robust cutting power and durability, allowing the mower to tackle various grass types and terrain with ease. The machine’s cutting deck is 21 inches wide, designed for precise cutting and efficient trimming, minimizing the time spent mowing while ensuring a clean cut every time.

The Snapper 020231 is equipped with a unique pivoting front wheel design, which enhances maneuverability around obstacles like trees, flower beds, and fences. This feature allows users to navigate tight spaces effortlessly, making yard work not only efficient but also less strenuous. Additionally, the adjustable cutting height feature offers multiple height positions, allowing users to customize their mowing experience based on the type of grass and desired finish.

One of the highlights of Snapper’s innovation is the easy-to-use, self-propelled feature available in the 020231. This technology allows users to set their desired speed while the mower moves forward, reducing physical strain and allowing for a consistent mowing pace. Furthermore, the ergonomic handle provides extra comfort while mowing, allowing users to maintain control and stability.

Snapper has also integrated SmartMulch technology into the 020231 model. This unique mulching capability allows for efficient grass disposal by finely chopping clippings and returning them to the lawn. This not only nourishes the soil but also eliminates the need for bagging and disposal, contributing to a healthier lawn ecosystem.

Safety features are paramount with the Snapper 020231. The operator presence control ensures that the engine stops when the handle is released, preventing accidental starts and enhancing user safety. Additionally, the durable construction and high-quality materials used in the mower's design ensure its longevity, making it a worthy investment for any homeowner or professional landscaper.

In conclusion, Snapper 020231 stands out as a high-quality, efficient, and reliable lawn mower that meets the diverse needs of its users. With its powerful engine, advanced technologies, and user-friendly design, it promises to deliver the performance and reliability users expect from the Snapper brand in every mowing task.
Top Page Image Contents