La Crosse Technology WS-8025SU III. Explanation of LCD Information, IV. Function Key Layout

III. Explanation of LCD Information

A. The below picture highlights the LCD features

WWVB reception indicator

Radio-controlled time	TIME	DATE	Alarm on indicator
	WWWB		Radio-controlled date

A.Overview of programming mode sequence

Note : If the country setting is other than USA step 8 is city, step 9 is time zone, etc.

1.	Hour	2.	Minute	3.	12/24 hour	4.	Year
5.	Month	6.	Date	7.	Country	8.	State
9.	City	10. Time Zone		11.	DST on/off	12. ˚F/˚C

Sunrise time for selected location

Sunset time for selected location

City code for city selected (San Francisco, USA shown)

Indoor temperature

	SUNRISE	MOON PHASE		MOONRISE +1		Moonset time for
						selected location
						Current moon phase
PM			PM			Moonset time for
	SUNSET	LOCATION		MOONSET		selected location
INDOOR TEMPERATURE			HUMIDITY			Indoor humidity
			%
					RH	Comfort icon
TENDENCY

13. inHg/hPa	14.	Relative pressure	15. Forecast	16.Storm warning
		setting	sensitivity	setting
17. Storm alarm	18.	LCD contrast	19. LI on/off
on/off

B. Time, 12/24 Hour Mode and Date Setting

The WWVB signal will override any manual set time and date information. The time will be

Air pressure tendency arrow (increase displayed)

Relative or absolute air pressure selection (relative shown)

Barometric air pressure

Pressure change over last two hours (in hPa)

(+4 hPa shown)

PRESSURE rel

inHg

PRESSURE HISTORY

+7

+5

+3

+1

0 -1 -3 -5 -7

-30h -24h -18h -12h -9h -6h -3h -1h 01

0 +0.2 +0.5 +1 +2 +4

Forecast icon

Measuring unit for air pressure, inHg shown

Last 30 hour air pressure graph

based on the time zone selected.
1.	Press and hold the "SET" button for 1 second.
2.	The hour is now flashing.
3.	Press and release the "+" or "-" button to select the current hour.

Note : In 12h mode "PM" will appear to the left of the time during PM hours. If the time is not within the PM hours nothing will be displayed. Be sure to set the time to the correct AM/ PM time to ensure automatic reception.

Remote temperature	OUTDOOR TEMPERATURE				HUMIDITY	%		Remote humidity
								Remote sensor number
			2			RH
Remote temperature								(up to three total)
					%	%
minimum and maximum	LO	HI						Remote humidity
	MIN	MAX		MIN	RH MAX		RH
OR alarm setting								minimum and maximum

B. There are many different modes the indoor weather station can be set to. The LCD shown is the normal operating mode, and your actual data shown will be different based on your local settings and conditions.

IV. Function Key Layout

A. The below picture shows the eight function keys used in programming and operation of your indoor weather station.

MIN MAX MIN MAX

IN	SUN/
	MOON
OUT	CH
ALARM	+
SET	–

V.Program Mode

The program mode is laid out in a manner that allows you to program each function separately, or you can follow the instructions entirely to program the indoor weather center. Complete programming is usually done for the initial set-up, and will require you to skip step 1 and 2 of each programming section. The programming mode can be exited at any time by either pressing the "CH" button, or waiting for the 16-second time-out to take effect.

4.Press the "SET" button to advance to the minute

5.The minute is now flashing.

6.Press and release the "+"or "-" button to select the current minute.

7.Press and release the "SET" button to advance to the 12/24-hour setting.

8."12" is now flashing.

9.Press and release the "+"or "-" button to select either 12 (am/pm) or 24 hour (military) time format.

10.Press and release the "SET" button to advance to the year setting.

11.The year is now flashing.

12.Press and release the "+"or "-" button to select the current year.

13.Press and release the "SET" button to advance to the month setting.

14.The month is now flashing.

15.Press and release the "+"or "-" button to select the current month.

16.Press and release the "SET" button to advance to the date setting.

17.The date is now flashing.

18.Press and release the "+"or "-" button to select the current date.

19.Press and release the "SET" button to advance to the location setting (skip steps 1 and 2 in section B if continuing).

C.City Location Setting

The list of the cities available is listed after this section.

1.Press and hold the "SET" button for 1 second.

2.Press and release the "SET" button 6 times.

3.The country location will flash (USA default/factory setting).

4.Press and release the "+"or "-" button to select the country (USA=United States, CAN=Canada, MEX=Mexico).

5.Press and release the "SET" button to advance to the state setting (USA only) or the city location (Canada or Mexico).

GB P.6 P.7 GB