Cub Cadet 7000 Series manual Starting the Engine, Cold Weather Starting, Stopping the Engine

Page 20

STARTING THE ENGINE

WARNING: Always sit in the operator’s seat when starting the tractor, Never attempt to start the engine while standing beside the tractor.

WARNING: Never use starting fluids, such as ether, as a starting aid. Severe engine damage or fire could result.

•Check the engine oil and coolant levels.

•Operator must be sitting in the tractor seat.

•Move the throttle handle to the full (FAST) throttle position. Refer to Figure 14.

•Make sure the PTO switch is in the “OFF” position. Note: The PTO light on instrument panel will flash if switch is in ON position.

THROTTLE

HANDLESLOW

FAST

PTO SWITCH

IN ‘OFF’

POSITION

Figure 14

•Either fully depress and hold the brake pedal or engage the parking brake. Note: The parking brake indicator on instrument panel will flash if pedal is not depressed.

•Turn the ignition key clockwise to the "RUN- PREHEAT" position, and observe the glow plug indicator light on the instrument panel. Wait until the glow plug indicator light turns off before cranking the engine.

NOTE: Preheating may not be necessary if the engine has been running and is warm.

•Turn the ignition key to the “START” position and release it as soon as the engine starts; however, do not crank the engine continuously for more than 20 seconds at a time. If the engine does not start within this time, turn the key to “OFF” and wait at least one minute to allow the engine’s starter motor to cool. Try again after waiting.

•After the engine has started, slowly move the throttle lever to the idle position. Allow the engine to idle for approximately three to five minutes before putting the engine under load.

•Observe the instrument panel. If the battery indicator light, oil pressure light, or coolant temperature light comes on, immediately stop the engine. Have the tractor inspected by your Cub Cadet dealer.

COLD WEATHER STARTING

Ensure that the correct viscosity grade of lubricating oil is used for the ambient temperature range in which the engine will run, as shown in the lubrication table in the MAINTENANCE section of this manual. Place the throttle control in the low idle (SLOW) position if the temperature is below 32°F (0°C), then follow the normal engine starting instructions above. Allow the engine additional time to warm up.

USING JUMPER CABLES TO START ENGINE

WARNING: Batteries contain sulfuric acid and produce explosive gasses. Make certain the area is well ventilated, wear gloves and eye protection, and avoid sparks or flames near the battery.

If the battery loses power and is unable to adequately crank the engine to start it, the aid of a booster battery may be necessary. Connect the booster battery as follows:

•Connect the ends of one jumper cable to the positive terminals of both the disabled tractor battery and the booster battery.

•Connect one end of the other cable to the booster battery’s negative terminal.

•Connect the other end of that cable to the engine block or frame of the disabled tractor, as far from the battery as possible.

•Start the disabled tractor following the normal starting instructions previously provided; then disconnect the jumper cables in the exact reverse order of connection.

•Have the tractor’s electrical system checked and repaired as soon as possible to eliminate the need for jump starting.

STOPPING THE ENGINE

•Place the PTO switch in the “OFF” position.

•Place the throttle control as follows:

-If the engine has been operated at low loads, place the throttle control lever in the “SLOW” position and allow the engine to idle for about one minute.

-If the engine has been operated at high load, run the engine at approximately 1/2 throttle for three to five minutes to reduce the engine coolant and oil temperatures. Then move the throttle control to the "SLOW" position.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 184VSHYGXW%OXMIRKIWIPPWGLEJX¤7EEVFVµGOIR¤+IVQER English Français Deutsch To the Owner Table of ContentsCalling Service Information Rops Information Plate Recording Model and Serial Number InformationTractor Model Plate Using the Tractor Correctly Important Safe Operation Practices General OperationSlope Operation ChildrenOperating the PTO Do notSafety Frame Rops ServiceSymbols on the appliance Starting AID Located Under Hood Safety LabelsFAN Warning Label Located on Each Side of Radiator Roll Over Warning Label Located on RIGHT/REAR Fender Battery Warning Label Located Under HoodPTO Warning Label Located on Rear PTO Shield Controls and Features Floorboard and Dash Panel Mounted ControlsPTO Switch Ignition SwitchSeat Adjustment Lever Steering WheelHazard Light Switch Headlight SwitchDifferential Lock Pedal Parking Brake LeverBattery Indicator Light Engine Coolant Temperature LightParking Brake Indicator Light PTO Indicator LightFender Mounted Conrtols and Features PTO Reverse Override SwitchFuel Fill Cap PTO Selection LeverTransmission Hi/Lo Range Shift Lever Cup HolderHand Holds Amber Hazard LightsFolding the Rops OperationRollover Protective Structure Rops Fueling the Tractor Safety Interlock SystemNEW Tractor BREAK-IN Procedures Using Jumper Cables to Start Engine Starting the EngineCold Weather Starting Stopping the EngineUsing the FORWARD/REVERSE Pedal Driving the TractorDriving on Slopes Stopping the TractorLOW Using the HI/LO Range Shift LeverUsing the Differential Lock Pedal Engaging the PTO Using the Hydraulic Lift LeverUsing the PTO Selection Lever Using the PTO Reverse Override Switch Using the TOP Link Retainer HookHazard Lights LightingUsing the Three Point Hitch Using the Hitch PlateUsing the Auxiliary Hydraulic Valve Using the Auxiliary Hydraulic Control HandleTractor Weighting On Demand Four Wheel DriveAdjustments Adjusting the SeatAdjusting the Seat Belt Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Check the TOE-IN AS FollowsAdjusting the Brakes Adjusting Hydraulic Lift Feedback RODGeneral Information MaintenanceLubrication Table Lubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart Service Intervals Operation toAccessing the Engine Compartment General Battery InformationBattery Removal Charging the BatteryBattery Maintenance Battery StorageTail Light Bulb Replacement Head Light Bulb ReplacementHazard Bulb Replacement Accessing the Fuse Center Servicing Electrical SystemInstrument Panel Fuses RelaysHazard Light Flasher Relay Checking TRANSMISSION/HYDRAULIC System OIL LevelInitial Break-In Period Filter Change Changing TRANSMISSION/HYDRAULIC System OILRegularly Scheduled Oil Filter Changes Check Front Axle OilCheck Final Reduction Gear Case Oil Changing Front Axle and Final Reduction Gear Case OILMaintenance of the Rollover Protective Structure Rops Tire MaintenanceLubrication of Main Drive Shaft Lubrication of FWD Drive ShaftTractor Storage Removing the Tractor from StorageEngine Maintenance Cleaning the EngineCleaning RADIATOR/RADIATOR Screen Checking Engine OIL LevelAdding Engine OIL Changing the Engine OIL and FilterChecking Engine Coolant Level Changing the Engine Coolant Changing the AIR CleanerInspection of Cooling System Hoses Changing The Fuel Filter Servicing the Fuel FilterDraining The Fuel Filter Engine Breather Service Fuel Injector Nozzle ServiceSpecifications Optional Equipment and Accessories HOW to Obtain Service 073URGXFWV$NWLHQJHVHOOVFKDIW

7000 Series specifications

The Cub Cadet 7000 Series is a line of premium lawn tractors designed for homeowners who seek both performance and durability in their gardening equipment. With a robust build quality and innovative features, the 7000 Series enhances the mowing experience, making it efficient and enjoyable.

One of the standout features of the 7000 Series is its powerful engine options. Equipped with Kohler and Kawasaki twin-cylinder engines, these tractors offer impressive horsepower that translates into higher mowing speeds and superior cutting performance. The engines are designed to provide reliable starting and increased torque, making them suitable for tackling thick grass and uneven terrain.

The series also highlights a superior cutting system. With a 48 to 54-inch cutting deck, the 7000 Series provides a precise and clean cut, allowing users to achieve a manicured lawn. The cutting decks are constructed with durable materials and feature a reinforced edge, ensuring longevity and resistance to wear over time. The decks come with adjustable cutting heights, giving users the flexibility to choose the perfect height for their lawn conditions.

Incorporating advanced technology, the Cub Cadet 7000 Series features a premium hydrostatic transmission. This system offers smooth and effortless speed control and allows for seamless transitions between forward and reverse. The intuitive controls facilitate maneuverability, making it easy for users to navigate around obstacles in their yard.

Comfort and convenience are paramount in the design of the 7000 Series. The tractors come equipped with fully adjustable, high-back ergonomic seats that provide excellent support during extended mowing sessions. Additionally, the dashboard is designed with maximized visibility, offering users clear insights into the tractor's operations and available features.

To enhance productivity, the 7000 Series is compatible with a range of accessories, including mulch kits, baggers, and snow removal attachments. These attachments increase the versatility of the tractors, allowing users to efficiently manage seasonal tasks beyond mowing.

In conclusion, the Cub Cadet 7000 Series combines power, durability, and convenience, making it a top choice for homeowners seeking a high-performance lawn tractor. With impressive cutting capabilities, advanced technologies, and ergonomic design, this series is well-suited for anyone looking to maintain their lawn with ease and efficiency. Whether for regular mowing or seasonal yard work, the 7000 Series stands out as a reliable and practical choice.
Top Page Image Contents